Daily Papers

Vision-language-action policies may predict a transferable manipulation strategy yet fail to realize it reliably on the encountered object: objects compatible with the same grasp differ in geometry and compliance, and visual feedback degrades under closure occlusion. AgenticTactileVLA is presented as an execution-time supervisor that shifts part of object-specific adaptation from prediction to physical interaction. A fixed VLA provides the approach and hand targets; the supervisor decides whether to remain transparent, refine finger flexion, retain or release the corrected configuration, return control to the VLA for retry, or select a compliant hand-control regime. It uses finger-position and motor-effort feedback as proprioceptive contact evidence and requires neither tactile sensors nor VLA retraining. On a Unitree G1 with a BrainCo Revo2 hand, a randomized matched-block evaluation on five objects held out from VLA training yields 61.3% completion for the base VLA, 72.0% for unconditional close-to-stall control, and 84.0% for the supervisor under a shared budget; the gain is positive on every object and persists under moderate pose perturbations. Ablations show the gain is not explained by extended closure alone, and that selective triggering reduces correction episodes by 65.7% with no detected change in completion. A retention audit shows acceptance predicts retention in 88.9% of held-out cases, while compliant objects expose conservative false rejection. A thin-walled-cup study demonstrates contextual routing to compliant control, matching an always-compliant reference. These results suggest that contact-guided execution-time adaptation can improve the object-level generalization of a fixed VLA to held-out objects by adapting physical realization without object-specific retraining.

Dexterous robot hands can receive useful motion intent from teleoperation or learned policies, but successful execution also depends on contact decisions that these commands rarely specify. We introduce DexFLEX, a contact-aware foundation controller that turns upstream fingertip-motion drafts into contact-consistent joint commands. Instead of treating a draft as a trajectory to copy, DexFLEX treats it as evidence about intent: from the current tactile-proprioceptive state, it proposes feasible short-horizon motion chunks, predicts their contact consequences, and selects the candidate that best follows the command while preserving future contact stability. At inference time, a simple Draft-Dream-Select procedure combines pure-prior proposals for recovery with draft-seeded proposals for responsiveness, then decodes the selected motion into executable joint-space targets. Across degraded-command simulation, real-world shared control, and visuomotor policy learning, the same trained controller improves robustness without retraining, increasing real-world teleoperation success from 29.2% to 78.3% and reaching 46.7% policy-learning success, 3.5 times direct joint-action prediction, and 1.56 times prior-only correction. Videos are available at dex-flex.github.io.

Proprioception is the "sixth sense" that detects limb postures with motor neurons. It requires a natural integration between the musculoskeletal systems and sensory receptors, which is challenging among modern robots that aim for lightweight, adaptive, and sensitive designs at a low cost. Here, we present the Soft Polyhedral Network with an embedded vision for physical interactions, capable of adaptive kinesthesia and viscoelastic proprioception by learning kinetic features. This design enables passive adaptations to omni-directional interactions, visually captured by a miniature high-speed motion tracking system embedded inside for proprioceptive learning. The results show that the soft network can infer real-time 6D forces and torques with accuracies of 0.25/0.24/0.35 N and 0.025/0.034/0.006 Nm in dynamic interactions. We also incorporate viscoelasticity in proprioception during static adaptation by adding a creep and relaxation modifier to refine the predicted results. The proposed soft network combines simplicity in design, omni-adaptation, and proprioceptive sensing with high accuracy, making it a versatile solution for robotics at a low cost with more than 1 million use cycles for tasks such as sensitive and competitive grasping, and touch-based geometry reconstruction. This study offers new insights into vision-based proprioception for soft robots in adaptive grasping, soft manipulation, and human-robot interaction.

Can embodied task agents use tactile experience to perform fine manipulation without task-specific model training? We investigate this capability through Tactile-ETA, a system that incorporates tactile experience into an embodied task agent through in-context learning. Successful expert demonstrations show how contact changes during manipulation. We pair each recorded robot movement with its camera views and bilateral tactile observations. We keep tactile observations at the start and end of each movement and add two neighboring time points when the tactile images change markedly in between. The agent combines these demonstrations with current vision, tactile observations, and proprioception to select actions through general-purpose robot tools, without updating model parameters. Across four simulated manipulation tasks, adding tactile observations to the same two expert demonstrations increases average success from 15.75% to 24.00%, with current sensing and execution interfaces held fixed. Further experiments show that performance depends on the sensory content and representation of demonstrations, while comparing agent models on Lift Bottle reveals substantial differences under the same system configuration. On the real-robot tasks, demonstrations with aligned visual and tactile observations increase the task success rate from 0% to 60%. These findings demonstrate the feasibility of using tactile experience in context for fine manipulation and suggest a path toward extending embodied task agents to additional sensory inputs.

We present blind, whole-body manipulation skills on a Unitree G1 humanoid using only onboard proprioception, without cameras, markers, force-torque, or tactile sensors. Despite this minimal sensing, the trained policies exhibit surprising capability across qualitatively different tasks: push-resilient bipedal walking without IMU feedback, active soccer ball trapping with a foot, seeking and lifting a suitcase by its handle, and mounting a randomly positioned skateboard. We argue that these capabilities arise from a key underappreciated signal: the way the joint encoder readouts evolve under purposeful compliant contact, effectively forming a whole-body tactile channel. By generating contact-rich motions, the trained policies actively probe the environment; as a result, task-relevant object state (e.g., pose) becomes increasingly decodable from short proprioceptive histories. We expose this information using compact task-specific state estimators trained alongside, but fully separately from, the policies; their prediction errors decrease rapidly after informative contact. Our results indicate that joint encoder-based proprioception, combined with compliant actuation (now widely available on commercial robots and low-cost motors) is already a strong, practical substrate for whole-body dexterous manipulation and interactive perception, and therefore a natural foundation on which richer sensing can be layered.

Large-scale egocentric human interaction data is becoming an important source of physical supervision for embodied learning, yet video alone leaves the contact and pressure that characterize physical interaction unrecorded. Recent visual-tactile datasets provide this missing supervision, but their synchronized tactile data remain far smaller in volume than human video. Moreover, the largest resources often merge recordings from different sensors or annotation procedures, which makes the effect of data scale difficult to isolate. We therefore introduce TouchScale, a 500-hour dataset of contact-rich human interaction recorded with a single unified wearable setup. Its approximately 2K predefined task descriptions span everyday activities and structured manipulation, and each recording temporally aligns egocentric RGB-D video with wrist RGB video and dense full-hand bimanual tactile measurements. Compared with prior tactile data, training on the full TouchScale raises zero-shot contact IoU on data from an unseen tactile sensor from 0.134 to 0.383. Pretraining a visual encoder on TouchScale also yields the highest action recognition accuracy on three benchmarks among the compared visual-tactile datasets. Used for visual-tactile mid-training of a robot policy, TouchScale improves the average real-world success rate across four contact-rich manipulation tasks from 22.5% to 57.5%. With the sensor and collection protocol held fixed, both zero-shot tactile prediction and robot success show an overall upward trend as more TouchScale data is used. These results suggest that human visual-tactile data collected at scale with consistent sensing benefits both perception and robot manipulation. We will publicly release TouchScale, including all synchronized visual-tactile recordings and reconstructed object models, to support future research on scalable visual-tactile learning.

Imitation learning models for robotic tasks typically rely on multi-modal inputs, such as RGB images, language, and proprioceptive states. While proprioception is intuitively important for decision-making and obstacle avoidance, simply incorporating all proprioceptive states leads to a surprising degradation in imitation learning performance. In this work, we identify the underlying issue as the proprioception shift problem, where the distributions of proprioceptive states diverge significantly between training and deployment. To address this challenge, we propose a domain adaptation framework that bridges the gap by utilizing rollout data collected during deployment. Using Wasserstein distance, we quantify the discrepancy between expert and rollout proprioceptive states and minimize this gap by adding noise to both sets of states, proportional to the Wasserstein distance. This strategy enhances robustness against proprioception shifts by aligning the training and deployment distributions. Experiments on robotic manipulation tasks demonstrate the efficacy of our method, enabling the imitation policy to leverage proprioception while mitigating its adverse effects. Our approach outperforms the naive solution which discards proprioception, and other baselines designed to address distributional shifts.

Humanoid parkour policies can traverse various terrains, but task completion may mask challenges of harsh landings, edge contacts, and unstable stance contacts. Humans naturally regulate foot-terrain interaction through tactile feedback, modulating contact compliance according to terrain stiffness. This highlights a key domain gap between humans and humanoid robots: the absence of rich tactile sensing in most humanoid systems. We address this problem with TactileStep, a deployable tactile learning framework that brings sole pressure sensing into humanoid locomotion control for softer touchdowns and more stable support. TactileStep aligns tactile simulation with the real pressure insole, allowing the policy to learn from the same contact features available on hardware. During training, we use tactile and motion cues to recognize different foot-contact phases and apply phase-aware rewards that encourage safer landing and more stable stance. Evaluated in simulation and on a Unitree G1 humanoid across diverse terrains, TactileStep reduces peak touchdown force by up to 48.8% and peak A-weighted impact noise by up to 30.1 dB over a strong perceptive baseline, while increasing stance contact area by up to 23.8%.

Contact-rich dexterous manipulation with multi-finger hands remains an open challenge in robotics because task success depends on multi-point contacts that continuously evolve and are highly sensitive to object geometry, frictional transitions, and slip. Recently, tactile-informed manipulation policies have shown promise. However, most use tactile signals as additional observations rather than modeling contact state or how their action outputs interact with low-level controller dynamics. We present Contact-Grounded Policy (CGP), a visuotactile policy that grounds multi-point contacts by predicting coupled trajectories of actual robot state and tactile feedback, and using a learned contact-consistency mapping to convert these predictions into executable target robot states for a compliance controller. CGP consists of two components: (i) a conditional diffusion model that forecasts future robot state and tactile feedback in a compressed latent space, and (ii) a learned contact-consistency mapping that converts the predicted robot state-tactile pair into executable targets for a compliance controller, enabling it to realize the intended contacts. We evaluate CGP using a physical four-finger Allegro V5 hand with Digit360 fingertip tactile sensors, and a simulated five-finger Tesollo DG-5F hand with dense whole-hand tactile arrays. Across a range of dexterous tasks including in-hand manipulation, delicate grasping, and tool use, CGP outperforms visuomotor and visuotactile diffusion-policy baselines.

Imitation-learning policies for robot manipulation inherit the quality of the success labels attached to their training episodes, and those labels are usually produced by the robot's own success check. A particularly damaging error is the false success: an episode the robot logs as a success when the task outcome was actually wrong. We ask a narrow but practical question about these episodes. Once an episode has already been flagged as a success, how much of the information needed to overturn that label is present in proprioception, and how much requires vision? We build a simulated testbed on two bimanual ALOHA tasks, induce failures through environment perturbations rather than label edits, label every episode by privileged simulator state that the detector never sees, and keep only episodes the robot flagged as successful. We then compare detectors restricted to proprioception against a vision-based detector. We find that recoverability spans a wide range: in cube transfer the false successes are almost fully recoverable from joint data alone, while in peg insertion proprioception recovers only part of them and a vision detector closes most of the gap. We also show that the proprioceptive separability we measure rests on velocity differences far below any realistic sensor noise floor, so it is best read as an optimistic upper bound that a noiseless simulator inflates. We release the generation and evaluation pipeline.

Learning contact-rich manipulation is difficult from cameras and proprioception alone because contact events are only partially observed. We test whether training-time instrumentation, i.e., object sensorisation, can improve policy performance without creating deployment-time dependencies. Specifically, we study button pressing as a testbed and use a microphone fingertip to capture contact-relevant audio. We use an instrumented button-state signal as privileged supervision to fine-tune an audio encoder into a contact event detector. We combine the resulting representation with imitation learning using three strategies, such that the policy only uses vision and audio during inference. Button press success rates are similar across methods, but instrumentation-guided audio representations consistently reduce contact force. These results support instrumentation as a practical training-time auxiliary objective for learning contact-rich manipulation policies.

Egocentric human video data, which captures rich human-environment interactions and can be collected at scale, has become a key driver of embodied intelligence research. However, existing egocentric datasets typically lack tactile sensing, a critical modality that provides direct cues about contact, force, and pressure in human-object interaction. Without such signals, models struggle to learn physically grounded representations of real-world interaction dynamics. While tactile sensors provide these cues, deploying high-quality tactile hardware at scale remains expensive and cumbersome. This raises a central question: can tactile feedback be inferred directly from visual observations, enabling scalable tactile supervision for egocentric video data and supporting physically grounded embodied learning? To enable research in this direction, we introduce EgoTouch, a large-scale multi-view egocentric dataset with dense tactile supervision for bimanual hand-object interaction. EgoTouch comprises 208 manipulation tasks spanning 1,891 episodes in diverse indoor and outdoor environments, with synchronized multi-view RGB (head-mounted egocentric and dual wrist-mounted cameras), bimanual 3D hand pose, and continuous pressure maps from wearable tactile sensors. Building on EgoTouch, we introduce TouchAnything, a baseline multi-view vision-to-touch prediction framework that uses the egocentric view as the primary input and flexibly leverages available wrist-mounted views at inference time. Experiments show that incorporating wrist-mounted views generally improves tactile prediction over egocentric-only input, achieving up to 5.0% relative improvement in Contact IoU and 6.1% relative improvement in Volumetric IoU. We will publicly release the dataset, code, and benchmark.

For both humans and robots, the sense of touch, known as tactile sensing, is critical for performing contact-rich manipulation tasks. Three key challenges in robotic tactile sensing are 1) interpreting sensor signals, 2) generating sensor signals in novel scenarios, and 3) learning sensor-based policies. For visuotactile sensors, interpretation has been facilitated by their close relationship with vision sensors (e.g., RGB cameras). However, generation is still difficult, as visuotactile sensors typically involve contact, deformation, illumination, and imaging, all of which are expensive to simulate; in turn, policy learning has been challenging, as simulation cannot be leveraged for large-scale data collection. We present TacSL (taxel), a library for GPU-based visuotactile sensor simulation and learning. TacSL can be used to simulate visuotactile images and extract contact-force distributions over 200times faster than the prior state-of-the-art, all within the widely-used Isaac Gym simulator. Furthermore, TacSL provides a learning toolkit containing multiple sensor models, contact-intensive training environments, and online/offline algorithms that can facilitate policy learning for sim-to-real applications. On the algorithmic side, we introduce a novel online reinforcement-learning algorithm called asymmetric actor-critic distillation (\sysName), designed to effectively and efficiently learn tactile-based policies in simulation that can transfer to the real world. Finally, we demonstrate the utility of our library and algorithms by evaluating the benefits of distillation and multimodal sensing for contact-rich manip ulation tasks, and most critically, performing sim-to-real transfer. Supplementary videos and results are at https://iakinola23.github.io/tacsl/.

Tactile sensing provides contact information that can be difficult to infer from vision alone, but tactile hardware for dexterous hands has not converged to a common design. Dexterous hands differ in finger structure, contact surfaces, and sensor layouts, while simulated tactile signals still differ from measurements produced by physical sensors. These factors make it difficult to study visuo-tactile manipulation across diverse dexterous hands within a consistent experimental setting. We present Bench2Dex, a simulation benchmark for visuo-tactile bimanual manipulation across 12 dexterous hands. We adapt existing robot models with a shared simulated tactile interface that converts local contact geometry into image-like tactile observations. The interface provides a consistent observation format across different hand morphologies without attempting to reproduce the output of a specific physical tactile sensor. Bench2Dex includes 26 bimanual manipulation tasks that involve tool use, articulated-object interaction, and multi-stage manipulation, together with about 1.3K human-teleoperated demonstrations. The benchmark provides synchronized visual, tactile, proprioceptive, action, and object-state observations, together with executable task metrics. For robustness, we group seven perturbation types into invariance axis, where the correct action does not change, and equivariance axis, where the correct action changes together with the perturbation. We evaluate ACT, Diffusion Policy, pi0.5, and GR00T N1.5 on Bench2Dex and report their performance and failure modes. Bench2Dex is meant as a platform for studying visuo-tactile learning across dexterous hands. It does not assume that simulated tactile observations can replace real tactile sensing; it offers a shared setting for algorithm development while tactile hardware and simulation models are still evolving.

We propose to address quadrupedal locomotion tasks using Reinforcement Learning (RL) with a Transformer-based model that learns to combine proprioceptive information and high-dimensional depth sensor inputs. While learning-based locomotion has made great advances using RL, most methods still rely on domain randomization for training blind agents that generalize to challenging terrains. Our key insight is that proprioceptive states only offer contact measurements for immediate reaction, whereas an agent equipped with visual sensory observations can learn to proactively maneuver environments with obstacles and uneven terrain by anticipating changes in the environment many steps ahead. In this paper, we introduce LocoTransformer, an end-to-end RL method that leverages both proprioceptive states and visual observations for locomotion control. We evaluate our method in challenging simulated environments with different obstacles and uneven terrain. We transfer our learned policy from simulation to a real robot by running it indoors and in the wild with unseen obstacles and terrain. Our method not only significantly improves over baselines, but also achieves far better generalization performance, especially when transferred to the real robot. Our project page with videos is at https://rchalyang.github.io/LocoTransformer/ .

Tactile sensing provides robots with direct observations of contact physics, local geometry, and interaction dynamics, making it a vital source of feedback for contact-rich manipulation. However, existing tactile manipulation studies are often developed and evaluated within specific task settings, making it difficult to systematically compare how tactile information contributes under different interaction conditions. In this work, we develop a benchmark in simulation comprising 128 tasks organized around three complementary evaluation regimes: Precise, Recognition, and Dynamic. The benchmark further includes controlled static and dynamic task variants and 12 perturbation settings for evaluating robustness under changes in visual and physical conditions. These settings motivate studying tactile information as a temporally evolving interaction representation rather than only as an instantaneous observation. We therefore propose an action-conditioned latent predictive world model that integrates tactile history and learns a tactile state through prediction of future tactile latents. Building on this representation, we design a model that conditions action generation on the learned tactile state and uses predicted future tactile information to refine candidate actions through predictive tactile reflection. Experiments on the proposed benchmark show consistent gains from incorporating tactile information across the evaluated regimes. Project Page: https://tacmind-bench.github.io/

Despite the importance of tactile sensing for reliable manipulation, most existing Vision-Language-Action (VLA) datasets remain vision-only, and those that do incorporate tactile information typically lack the joint combination of task diversity, language conditioning, and action trajectories. Furthermore, existing teleoperation pipelines rarely provide haptic feedback to the operator, despite its established role in demonstration quality and manipulation stability. In this work, we present HapTile, a contact-grounded visuotactile manipulation dataset that advances beyond vision-only trajectory datasets by embedding physical interaction sensing at two levels: fingertip tactile feedback at the robot end-effector, and haptic-informed demonstrations at the teleoperator side. The data collection platform integrates haptic feedback directly into the teleoperation controller, enabling the operator to perceive contact interactions in real time. It is built around a standard and reproducible robotic system equipped with custom-designed fingertip tactile sensors. The dataset comprises everyday manipulation tasks spanning a broad range of contact-rich skills, including pick-and-place, folding, pressing, stacking, and other routine activities. Each task is paired with language instructions that condition the policy on the manipulation objective, together with synchronized visuotactile observations and action trajectories. In addition, we provide a benchmarking study on contact-rich policy learning using two baseline models to evaluate the effectiveness of the proposed contact-grounded dataset. The dataset and additional details are available on our website: haptile-dataset.github.io.

Touch is a crucial sensing modality that provides rich information about object properties and interactions with the physical environment. Humans and robots both benefit from using touch to perceive and interact with the surrounding environment (Johansson and Flanagan, 2009; Li et al., 2020; Calandra et al., 2017). However, no existing systems provide rich, multi-modal digital touch-sensing capabilities through a hemispherical compliant embodiment. Here, we describe several conceptual and technological innovations to improve the digitization of touch. These advances are embodied in an artificial finger-shaped sensor with advanced sensing capabilities. Significantly, this fingertip contains high-resolution sensors (~8.3 million taxels) that respond to omnidirectional touch, capture multi-modal signals, and use on-device artificial intelligence to process the data in real time. Evaluations show that the artificial fingertip can resolve spatial features as small as 7 um, sense normal and shear forces with a resolution of 1.01 mN and 1.27 mN, respectively, perceive vibrations up to 10 kHz, sense heat, and even sense odor. Furthermore, it embeds an on-device AI neural network accelerator that acts as a peripheral nervous system on a robot and mimics the reflex arc found in humans. These results demonstrate the possibility of digitizing touch with superhuman performance. The implications are profound, and we anticipate potential applications in robotics (industrial, medical, agricultural, and consumer-level), virtual reality and telepresence, prosthetics, and e-commerce. Toward digitizing touch at scale, we open-source a modular platform to facilitate future research on the nature of touch.

Humans inherently understand the physical world through an active process. When sensory evidence is insufficient to infer physical properties, we naturally interact with the environment by deciding what information is missing, how to acquire it, and when sufficient evidence has been obtained. In stark contrast, existing multi-sensory robot systems mainly integrate sensory inputs rather than actively acquiring missing evidence through interactions. In this work, we introduce ROMA, an LLM-based system for Real-World Object-Centric Multi-Sensory Active Perception. ROMA integrates vision, audio, tactile, and force sensing into a reasoning-interaction-feedback loop. The model identifies missing evidence and determines the target objects, interactions, and modalities, while a physical interface executes the selected interactions and collects the multi-sensory feedback. To support this capability, we construct ROMI-2K, a large-scale real-world multi-sensory object interaction dataset covering nearly 2,000 objects and 6 atomic interactions with synchronized sensory feedback. Building on these data, we develop a two-stage training framework that aligns sensory modalities and equips the LLM to assess evidence sufficiency, select informative interactions, and reason over the multi-sensory feedback. We further characterize active perception as perception chains, where acquired evidence guides subsequent interactions and reasoning, and establish ROMA Bench to evaluate single-attribute, long-horizon multi-attribute, and intent-driven active perception. Experiments show that ROMA can actively acquire missing evidence and solve complex, long-chain multi-sensory perception tasks that existing methods struggle to handle, laying a strong perceptual foundation for active multi-sensory embodied agents.

We introduce multi-task Visuo-Tactile World Models (VT-WM), which capture the physics of contact through touch reasoning. By complementing vision with tactile sensing, VT-WM better understands robot-object interactions in contact-rich tasks, avoiding common failure modes of vision-only models under occlusion or ambiguous contact states, such as objects disappearing, teleporting, or moving in ways that violate basic physics. Trained across a set of contact-rich manipulation tasks, VT-WM improves physical fidelity in imagination, achieving 33% better performance at maintaining object permanence and 29% better compliance with the laws of motion in autoregressive rollouts. Moreover, experiments show that grounding in contact dynamics also translates to planning. In zero-shot real-robot experiments, VT-WM achieves up to 35% higher success rates, with the largest gains in multi-step, contact-rich tasks. Finally, VT-WM demonstrates significant downstream versatility, effectively adapting its learned contact dynamics to a novel task and achieving reliable planning success with only a limited set of demonstrations.

This paper presents a novel vision-based proprioception approach for a soft robotic finger that can estimate and reconstruct tactile interactions in both terrestrial and aquatic environments. The key to this system lies in the finger's unique metamaterial structure, which facilitates omni-directional passive adaptation during grasping, protecting delicate objects across diverse scenarios. A compact in-finger camera captures high-framerate images of the finger's deformation during contact, extracting crucial tactile data in real-time. We present a volumetric discretized model of the soft finger and use the geometry constraints captured by the camera to find the optimal estimation of the deformed shape. The approach is benchmarked using a motion capture system with sparse markers and a haptic device with dense measurements. Both results show state-of-the-art accuracies, with a median error of 1.96 mm for overall body deformation, corresponding to 2.1% of the finger's length. More importantly, the state estimation is robust in both on-land and underwater environments as we demonstrate its usage for underwater object shape sensing. This combination of passive adaptation and real-time tactile sensing paves the way for amphibious robotic grasping applications.

Rich contact perception is crucial for robotic manipulation, yet traditional tactile skins remain expensive and complex to integrate. This paper presents a scalable alternative: high-accuracy whole-body touch localization via vibro-acoustic sensing. By equipping a robotic hand with seven low-cost piezoelectric microphones and leveraging an Audio Spectrogram Transformer, we decode the vibrational signatures generated during physical interaction. Extensive evaluation across stationary and dynamic tasks reveals a localization error of under 5 mm in static conditions. Furthermore, our analysis highlights the distinct influence of material properties: stiff materials (e.g., metal) excel in impulse response localization due to sharp, high-bandwidth responses, whereas textured materials (e.g., wood) provide superior friction-based features for trajectory tracking. The system demonstrates robustness to the robot's own motion, maintaining effective tracking even during active operation. Our primary contribution is demonstrating that complex physical contact dynamics can be effectively decoded from simple vibrational signals, offering a viable pathway to widespread, affordable contact perception in robotics. To accelerate research, we provide our full datasets, models, and experimental setups as open-source resources.

Tactile sensing is particularly valuable for contact-rich robotic manipulation. Recent work has made substantial progress in tactile representation learning for robotic manipulation. However, similar tactile observations can arise from interaction conditions with very different task-risk implications, such as sensor noise, task-necessary variations, and emerging undesirable contact. Without context-grounded risk information, these cases can be ambiguous to downstream policies, leading to unnecessary corrections to benign variations or delayed responses to genuinely risky contact. To address this limitation, we propose Risk-Aware Tactile Encoding (RATE), which learns tactile representations that encode task-conditioned interaction risk. Specifically, history-conditioned prediction captures interaction context, while alert supervision associates this context with task-conditioned risk. The learned risk-aware representation complements conventional tactile features through a lightweight residual adapter. Experiments in both simulation and the real world demonstrate substantial improvements in task success, with controlled ablations confirming the complementary benefits of alert-guided learning and predictive temporal modeling.

Contact-rich manipulation requires estimating forces, slip and contact geometry that can remain ambiguous in scene images. Optical tactile sensors provide both visual observations of the contact surface and mechanical measurements, yet learning from these signals raises two challenges: representing contact beyond appearance and transferring its benefits to a policy that does not require fingertip observations at deployment. We introduce HapticWAM, a world-action model that combines heterogeneous tactile encoding, structured contact prediction and teacher-student distillation. Its teacher encodes gel images together with deformation, shear, distributed forces, resultant wrench and derived contact state into a frozen video backbone. Rather than predicting tactile pixels alone, the model jointly generates actions and a contact package describing future events and mechanics. Anticipatory Contact Coupling uses the previously imagined package to condition attention, preserving a contact-related input when direct tactile observations are unavailable. Haptic-Imagination Distillation transfers both contact futures and action predictions to a student that retains the generative contact head but removes its fingertip input branches. On a real-world setup, across three contact-rich pick-and-place tasks, HapticWAM Student achieves a 77% per-task mean success rate (41 of 50 starts, 82% pooled), reaching 95% on one of the tasks, outperforming the evaluated teacher and baseline configurations.

Contact-rich policies often fail because distinct physical states look alike yet require different actions. Cameras may not reveal whether a connector is aligned or fully seated, while many normal-only tactile sensors can miss the tangential interactions perpendicular to the grasping direction that distinguish these states. We ask whether a learning policy needs calibrated shear measurements, or only a repeatable observation that separates shear-dependent contact states. We introduce TacGooseBumps (TacGB), a passive domed film that mechanically encodes tangential loading as pattern changes in an existing sensor's pressure map. Tangential loading tilts each dome and redistributes pressure across its footprint; an end-to-end policy consumes the resulting maps without added electronics, force reconstruction, or taxel-level dome alignment. Across four imitation-learning tasks and two data-collection pipelines, TacGB improves goal attainment, efficiency, and contact quality: insertion success increases by up to 36 percentage points, and successful insertions are completed faster, while fragile-object placement becomes gentler and drawing becomes more continuous and straight. Signal, stage-wise, failure-mode, and trajectory analyses link these gains to contact regimes in which task-relevant tangential interactions are poorly resolved by vision and normal pressure alone. Together, these results show that shear need not be measured metrically to benefit robot learning; it can instead be mechanically encoded without changing the underlying tactile sensor or the policy's pressure-map input format.

Robotic grasping and surface exploration benefit from simultaneous measurement of normal and tangential forces and from surface information obtained through contact. Here, we present a compact magnetociliary tactile sensor (MagCilia) that combines a flexible magnetic-cilia structure with a Hall sensor for 3D force sensing. Quasi-static finite element analysis is used to investigate structural deformation and magnetic responses under multidirectional loading. To reconstruct forces from the coupled magnetic channels, we propose causal history fusion regression (CHFR), which combines current magnetic-field measurements with their recent changes. Five-fold cross-validation grouped by calibration record yields root-mean-square errors of 0.40, 0.57, and 0.69 N for Fx, Fy, and Fz, respectively, with corresponding coefficients of determination of 0.93, 0.90, and 0.92. Robotic experiments demonstrate tangential-force-guided gripper adjustment and multi-axis load monitoring under external perturbations. Frequency-domain features of the reconstructed forces distinguish six surface categories with 99.39% accuracy in three-fold cross-validation grouped by acquisition session. An online robotic demonstration additionally identifies all six tested surfaces. These results demonstrate 3D force reconstruction, grasping feedback, and surface recognition using a single compact tactile unit.

Understanding hand-object interaction from egocentric vision is essential for modeling how people physically engage with the surrounding world. Yet reasoning about physically grounded interaction requires estimating the forces acting on hands and objects, beyond localizing contact. We present EgoPHI, the first method that jointly estimates dense contact maps and 3D force distributions on hand and object meshes from a single monocular RGB image and object geometry. To address the lack of scalable ground-truth force annotations, we introduce a physics-based simulation pipeline that augments existing hand-object datasets with dense per-vertex force supervision. EgoPHI then learns dense 3D contact and force on interacting hand and articulated object meshes, extending vision-based force estimation beyond image-space or planar settings. Our evaluation on in-distribution and out-of-distribution benchmarks shows that EgoPHI improves force estimation over existing approaches while generalizing to unseen datasets. To evaluate sim-to-real transfer, we constructed two physical objects that capture dense object contact and force magnitude and used them to record a dataset of interactions from eight participants across diverse touch and grasp types. Our results demonstrate that EgoPHI recovers meaningful 3D contact and force distributions in simulated, out-of-distribution, and real-world settings, advancing egocentric hand-object understanding from contact localization toward physically grounded interaction reasoning.

Whole-arm manipulation involves direct contact with the environment while the robot completes a task by distributing contact across multiple links as contacts form, slide, and break. This setting breaks common implicit assumptions in many learning-based manipulation pipelines: arm configuration tightly couples motion and contact forces, contact state is partially observed under occlusion, and purely learned rollouts can become physically inconsistent under distribution shift because many multi-link contact configurations are sparsely represented in the data. To address this, we propose TACTIC (Tactile and Vision Conditioned Contact-Centric Control), a receding-horizon controller for whole-arm manipulation. TACTIC uses a contact-centric hybrid predictive model that combines RGB-D, distributed tactile sensing, and a compact 2D proximity representation. The model couples a learned, action-conditioned latent dynamics model with analytical kinematics through contact Jacobians, enabling rollouts of future contact configurations and interaction forces. TACTIC integrates these rollouts into a sampling-based MPC planner with contact-aware action sampling: contact Jacobian-based projections steer sampled action sequences toward force-modulating directions, and objectives defined over predicted proximity and interaction forces trade task progress against whole-arm force regulation. We evaluate TACTIC in simulation against state-of-the-art model-based and model-free methods, and perform ablations that isolate the contribution of each design choice. TACTIC consistently outperforms other methods. We further demonstrate real-world performance on a robot with distributed tactile sensing across three whole-arm manipulation tasks that require multi-contact trajectories: turning over and repositioning a manikin, and goal-reaching in a 3D dynamic maze. Website: https://emprise.cs.cornell.edu/tactic

Reinforcement learning explores effectively in domains such as Atari games, navigation, and locomotion, where novelty over states or dynamics is a sufficient signal. In contrast, dexterous manipulation requires rich physical hand--object interactions, but existing methods often suffer from unstable contact-based novelty signals, inefficient distance novelty signals, or reliance on task-specific priors. We propose ContactExplorer, a general exploration method for dexterous manipulation tasks. ContactExplorer represents contact as the intersection between object surface points and hand keypoints, encouraging dexterous hands to discover diverse and novel contact patterns, namely which fingers contact which object regions. It maintains a contact counter conditioned on discretized object states obtained via learned hash codes. This counter is leveraged in two complementary ways: (1) a count-based contact coverage reward that promotes exploration of novel contact patterns, and (2) an energy-based reaching reward that guides the agent toward under-explored contact regions. We evaluate ContactExplorer on seven contact-rich manipulation tasks and five dexterous hand embodiments. Experimental results show that ContactExplorer substantially improves sample efficiency and success rates over existing exploration methods, that it reduces the need for task-specific priors, and that it remains effective across hand embodiments and transfers to the real world. Project page is https://contact-explorer.github.io.

Embodied intelligence has advanced rapidly in recent years; however, bimanual manipulation-especially in contact-rich tasks remains challenging. This is largely due to the lack of datasets with rich physical interaction signals, systematic task organization, and sufficient scale. To address these limitations, we introduce the VTOUCH dataset. It leverages vision based tactile sensing to provide high-fidelity physical interaction signals, adopts a matrix-style task design to enable systematic learning, and employs automated data collection pipelines covering real-world, demand-driven scenarios to ensure scalability. To further validate the effectiveness of the dataset, we conduct extensive quantitative experiments on cross-modal retrieval as well as real-robot evaluation. Finally, we demonstrate real-world performance through generalizable inference across multiple robots, policies, and tasks.

Collecting demonstrations enriched with fine-grained tactile information is critical for dexterous manipulation, particularly in contact-rich tasks that require precise force control and physical interaction. While prior works primarily focus on teleoperation or video-based retargeting, they often suffer from kinematic mismatches and the absence of real-time tactile feedback, hindering the acquisition of high-fidelity tactile data. To mitigate this issue, we propose KineDex, a hand-over-hand kinesthetic teaching paradigm in which the operator's motion is directly transferred to the dexterous hand, enabling the collection of physically grounded demonstrations enriched with accurate tactile feedback. To resolve occlusions from human hand, we apply inpainting technique to preprocess the visual observations. Based on these demonstrations, we then train a visuomotor policy using tactile-augmented inputs and implement force control during deployment for precise contact-rich manipulation. We evaluate KineDex on a suite of challenging contact-rich manipulation tasks, including particularly difficult scenarios such as squeezing toothpaste onto a toothbrush, which require precise multi-finger coordination and stable force regulation. Across these tasks, KineDex achieves an average success rate of 74.4%, representing a 57.7% improvement over the variant without force control. Comparative experiments with teleoperation and user studies further validate the advantages of KineDex in data collection efficiency and operability. Specifically, KineDex collects data over twice as fast as teleoperation across two tasks of varying difficulty, while maintaining a near-100% success rate, compared to under 50% for teleoperation.

Learning from human video demonstrations remains challenging due to noisy hand-object interactions, unseen objects with partial observation, and cross-embodiment discrepancy. To address these challenges, we present HOWTransfer (Hand-Object Open-World Transfer), a hand-centric framework that distills human demonstrations into contact-aware, taxonomy-informed, and diverse robotic trajectories. Instead of relying on object-specific descriptions, vision-language queries, or explicit object-state tracking, HOWTransfer recovers temporally consistent 3D hand motion and localizes temporal contact intervals by reasoning over observed hand-object interaction cues. The localized contact onsets are then used to retarget human grasp intent into multi-modal parallel-jaw grasp hypotheses, which are propagated along the recovered wrist trajectory to generate robot-executable motions. Finally, a trajectory editing stage refines contact alignment and produces diverse executable variants from a single demonstration. Experiments across diverse manipulation tasks show that HOWTransfer enables accurate contact localization and high-quality robot motion retargeting with 86% success, which is preferred over teleoperated trajectories in a blinded preference study.

Vision-Language-Action (VLA) models have shown remarkable generalization by mapping web-scale knowledge to robotic control, yet they remain blind to physical contact. Consequently, they struggle with contact-rich manipulation tasks that require reasoning about force, texture, and slip. While some approaches incorporate low-dimensional tactile signals, they fail to capture the high-resolution dynamics essential for such interactions. To address this limitation, we introduce DreamTacVLA, a framework that grounds VLA models in contact physics by learning to feel the future. Our model adopts a hierarchical perception scheme in which high-resolution tactile images serve as micro-vision inputs coupled with wrist-camera local vision and third-person macro vision. To reconcile these multi-scale sensory streams, we first train a unified policy with a Hierarchical Spatial Alignment (HSA) loss that aligns tactile tokens with their spatial counterparts in the wrist and third-person views. To further deepen the model's understanding of fine-grained contact dynamics, we finetune the system with a tactile world model that predicts future tactile signals. To mitigate tactile data scarcity and the wear-prone nature of tactile sensors, we construct a hybrid large-scale dataset sourced from both high-fidelity digital twin and real-world experiments. By anticipating upcoming tactile states, DreamTacVLA acquires a rich model of contact physics and conditions its actions on both real observations and imagined consequences. Across contact-rich manipulation tasks, it outperforms state-of-the-art VLA baselines, achieving up to 95% success, highlighting the importance of understanding physical contact for robust, touch-aware robotic agents.

Tactile-enhanced vision-language-action (VLA) policies have been introduced for contact-rich manipulation, where critical interaction states are often hidden from vision. Future tactile prediction is a promising way to use touch because it turns tactile outcomes into supervision for action-induced contact dynamics. Yet VLA policies contain representations with different roles, from perceptual encoding to motor prediction, making it unclear where this supervision should be applied. We study this as a representation-alignment problem. Through a linear probe analysis, we find that future tactile states are most predictable from intermediate action-expert features, rather than from vision-language features or final action states. Motivated by this observation, we introduce a lightweight Latent Tactile Predictor (LTP), which predicts compact future tactile embeddings from the identified intermediate representation. By avoiding direct prediction of noisy raw tactile signals, LTP provides an action-outcome grounding signal that aligns intermediate action representations with future contact consequences. Experiments on real-world contact-rich manipulation tasks show that representation-aligned tactile grounding outperforms less aligned or multi-interface tactile prediction, highlighting the importance of where tactile supervision is applied.

Contact-rich manipulation failures are often detected only after the robot has committed to contact. This is especially limiting in wrist-camera setups: close gripper--object views help observe contact, but a poor approach may already push, miss, slip, or disturb the object before conventional detectors react. We introduce ContactGuard, a pre-contact execution monitor for chunked visuomotor policies. Given the policy's planned action chunk, ContactGuard predicts its short-horizon consequence in latent visual space and aborts if the predicted future latent indicates likely failure. Its latent world model is trained from unlabelled robot trajectories to predict compact multi-view visual embeddings under planned actions, avoiding pixel-level video prediction. A lightweight failure probe is then trained from a small labelled set of pre-contact clips. At deployment, ContactGuard anchors prediction before an imminent contact event, rolls the model forward under the policy's own actions, and verifies the predicted post-contact latent. Across real-world contact-rich manipulation tasks, ContactGuard predicts failure more accurately than direct and corrupted-action ablations, and transfers to live robot as a pre-contact abort signal without modifying the underlying policy.

Humans are dexterous, but traditional data collection paradigms such as teleoperation, kinesthetic teaching, and wearable exoskeletons force humans to act through the robot embodiment, bottlenecking their dexterity. Retargeting can avoid this. However, existing methods purely translate kinematics and ignore the real-world contact dynamics essential for task success. We present CARD: Contact-Anchored Retargeting for Dexterous Manipulation, a simulator and object-free framework that retargets human demonstrations to robot actions by explicitly preserving contact force targets. CARD unifies human data sources including video, motion capture, and tactile gloves via a shared hand--contact representation and generates explicit contact force targets in addition to kinematics. To maintain these contact targets during hardware open-loop replay, CARD also introduces a tactile tracking controller. For video which does not contain an explicit tactile source, we present Vid-HACO, our video-to-contact model that sets a new state of the art. Across our video, glove, motion-capture data and the GRAB dataset, CARD maintains contact on 43--78% of contact frames, while kinematic and object-aware retargeting methods maintain contact on <10% and 22.5% of the frames respectively. Further, integrating our formulation into physics-based retargeting improves strict task success from 12\% to 32\% on GRAB dataset. Finally, we show that our tactile tracker is critical to reproduce demonstrated forces during hardware replay. These results establish that contact preservation via CARD is a scalable interface for transferring human dexterity to robots.

Robots in many real-world settings have access to force/torque sensors in their gripper and tactile sensing is often necessary in tasks that involve contact-rich motion. In this work, we leverage surprise from mismatches in touch feedback to guide exploration in hard sparse-reward reinforcement learning tasks. Our approach, Touch-based Curiosity (ToC), learns what visible objects interactions are supposed to "feel" like. We encourage exploration by rewarding interactions where the expectation and the experience don't match. In our proposed method, an initial task-independent exploration phase is followed by an on-task learning phase, in which the original interactions are relabeled with on-task rewards. We test our approach on a range of touch-intensive robot arm tasks (e.g. pushing objects, opening doors), which we also release as part of this work. Across multiple experiments in a simulated setting, we demonstrate that our method is able to learn these difficult tasks through sparse reward and curiosity alone. We compare our cross-modal approach to single-modality (touch- or vision-only) approaches as well as other curiosity-based methods and find that our method performs better and is more sample-efficient.

Tactile information plays a crucial role for humans and robots to interact effectively with their environment, particularly for tasks requiring the understanding of contact properties. Solving such dexterous manipulation tasks often relies on imitation learning from demonstration datasets, which are typically collected via teleoperation systems and often demand substantial time and effort. To address these challenges, we present ViTaMIn, an embodiment-free manipulation interface that seamlessly integrates visual and tactile sensing into a hand-held gripper, enabling data collection without the need for teleoperation. Our design employs a compliant Fin Ray gripper with tactile sensing, allowing operators to perceive force feedback during manipulation for more intuitive operation. Additionally, we propose a multimodal representation learning strategy to obtain pre-trained tactile representations, improving data efficiency and policy robustness. Experiments on seven contact-rich manipulation tasks demonstrate that ViTaMIn significantly outperforms baseline methods, demonstrating its effectiveness for complex manipulation tasks.

Tactile sensing is critical to fine-grained, contact-rich manipulation tasks, such as insertion and assembly. Prior research has shown the possibility of learning tactile-guided policy from teleoperated demonstration data. However, to provide the demonstration, human users often rely on visual feedback to control the robot. This creates a gap between the sensing modality used for controlling the robot (visual) and the modality of interest (tactile). To bridge this gap, we introduce "MimicTouch", a novel framework for learning policies directly from demonstrations provided by human users with their hands. The key innovations are i) a human tactile data collection system which collects multi-modal tactile dataset for learning human's tactile-guided control strategy, ii) an imitation learning-based framework for learning human's tactile-guided control strategy through such data, and iii) an online residual RL framework to bridge the embodiment gap between the human hand and the robot gripper. Through comprehensive experiments, we highlight the efficacy of utilizing human's tactile-guided control strategy to resolve contact-rich manipulation tasks. The project website is at https://sites.google.com/view/MimicTouch.

Tactile sensing is an essential modality for robots performing contact-rich, dexterous manipulation, particularly under visual occlusion. While pre-trained image encoders are standard in robot learning pipelines, tactile encoders are still commonly trained from scratch from raw, noisy signals, which might limit their expressivity. Existing self-supervised learning (SSL) approaches focus predominantly on vision-based tactile sensors, leaving distributed electronic skins largely unaddressed. These sensors, however, have a distinctive property: their sensing elements are sparse and irregularly arranged over the surface they cover, which makes direct reuse of visual SSL methods suboptimal. We present Tactile-JEPA, an efficient self-supervised pre-training method that uses the spatial arrangement of tactile sensors to learn topology-aware representations. Specifically, it is trained to predict the embeddings of masked sensing elements from the unmasked remainder, using the sensor connectivity graph to guide spatial masking. Our analysis shows that effective tactile representations require capturing both local contact details and the global state of the tactile surface, which we achieve through dual-scale masking. Across three diverse datasets spanning magnetic and piezoresistive sensors, different robot embodiments, and single- and paired-sensor configurations, Tactile-JEPA reduces force estimation error by 6.3% and in-hand orientation error by 20.8% over the prior state-of-the-art, with consistent gains in other downstream applications, including policy learning. Overall, our results demonstrate that the benefit of tactile sensing depends critically on the quality of encoder pre-training, a problem which Tactile-JEPA addresses directly. Code is available at https://github.com/E-Kovtun/tactile.

The human hand is our primary interface to the physical world, yet egocentric perception rarely knows when, where, or how forcefully it makes contact. Robust wearable tactile sensors are scarce, and no existing in-the-wild datasets align first-person video with full-hand touch. To bridge the gap between visual perception and physical interaction, we present OpenTouch, the first in-the-wild egocentric full-hand tactile dataset, containing 5.1 hours of synchronized video-touch-pose data and 2,900 curated clips with detailed text annotations. Using OpenTouch, we introduce retrieval and classification benchmarks that probe how touch grounds perception and action. We show that tactile signals provide a compact yet powerful cue for grasp understanding, strengthen cross-modal alignment, and can be reliably retrieved from in-the-wild video queries. By releasing this annotated vision-touch-pose dataset and benchmark, we aim to advance multimodal egocentric perception, embodied learning, and contact-rich robotic manipulation.

Dexterous manipulation depends on contact dynamics that are often only partially observable from vision. Recent World-Action Models (WAMs) couple predictive video world modeling with action generation, but remain largely vision-centric and therefore cannot directly model these contact dynamics. We present DexTacWAM, a visuo-tactile WAM that encodes each fingertip independently, aggregates the resulting features through a finger- and pose-aware tactile compressor, and injects the tactile latent into a video diffusion world model for joint visuo-tactile world modeling. Across six contact-rich dexterous manipulation tasks on a 22-DoF bimanual platform, DexTacWAM achieves the highest score on every task, averaging 70.6 versus 38.0 for the strongest baseline. Ablations attribute the gain to modeling contact evolution as part of the predicted world state rather than tactile conditioning alone: removing tactile world modeling reduces the four-task mean from 74.7 to 26.6 while keeping the same tactile features and action expert. After four hours of tactile-encoder adaptation with a frozen pretrained vision VAE, our continual vision-to-touch learning extends the pretrained video model to touch using roughly 100 demonstrations per task without tactile midtraining, while retaining visual prediction quality within 0.5 dB of vision-only counterparts. The compressor retains 89.4% of pre-fusion contact recall while enabling 2.26x faster training and 1.29x faster inference. Together, these results show that pretrained video priors can be extended to distributed multi-finger contact dynamics in a data- and compute-efficient manner.

We address the challenging task of detecting the precise moment when hands make contact with objects in egocentric videos. This frame-level detection is crucial for augmented reality, human-computer interaction, assistive technologies, and robot learning applications, where contact onset signals action initiation or completion. Temporally precise detection is particularly challenging due to subtle hand motion variations near contact, frequent occlusions, fine-grained manipulation patterns, and the inherent motion dynamics of first-person perspectives. To tackle these challenges, we propose a Hand-informed Context Enhanced module (HiCE; pronounced `high-see') that leverages spatiotemporal features from hand regions and their surrounding context through cross-attention mechanisms, learning to identify potential contact patterns. Our approach is further refined with a grasp-aware loss and soft label that emphasizes hand pose patterns and movement dynamics characteristic of touch events, enabling the model to distinguish between near-contact and actual contact frames. We also introduce TouchMoment, an egocentric dataset containing 4,021 videos and 8,456 annotated contact moments spanning over one million frames. Experiments on TouchMoment show that, under a strict evaluation criterion that counts a prediction as correct only if it falls within a two-frame tolerance of the ground-truth moment, our method achieves substantial gains and outperforms state-of-the-art event-spotting baselines by 16.91% average precision.

Imitation learning provides a promising approach to dexterous hand manipulation, but its effectiveness is limited by the lack of large-scale, high-fidelity data. Existing data-collection pipelines suffer from inaccurate motion retargeting, low data-collection efficiency, and missing high-resolution fingertip tactile sensing. We address this gap with MILE, a mechanically isomorphic teleoperation and data-collection system co-designed from human hand to exoskeleton to robotic hand. The exoskeleton is anthropometrically derived from the human hand, and the robotic hand preserves one-to-one joint-position isomorphism, eliminating nonlinear retargeting and enabling precise, natural control. The exoskeleton achieves a multi-joint mean absolute angular error below one degree, while the robotic hand integrates compact fingertip visuotactile modules that provide high-resolution tactile observations. Built on this retargeting-free interface, we teleoperate complex, contact-rich in-hand manipulation and efficiently collect a multimodal dataset comprising high-resolution fingertip visuotactile signals, RGB-D images, and joint positions. The teleoperation pipeline achieves a mean success rate improvement of 64%. Incorporating fingertip tactile observations further increases the success rate by an average of 25% over the vision-only baseline, validating the fidelity and utility of the dataset. Further details are available at: https://sites.google.com/view/mile-system.

Touch contact and pressure are essential for understanding how humans interact with and manipulate objects, insights which can significantly benefit applications in mixed reality and robotics. However, estimating these interactions from an egocentric camera perspective is challenging, largely due to the lack of comprehensive datasets that provide both accurate hand poses on contacting surfaces and detailed annotations of pressure information. In this paper, we introduce EgoPressure, a novel egocentric dataset that captures detailed touch contact and pressure interactions. EgoPressure provides high-resolution pressure intensity annotations for each contact point and includes accurate hand pose meshes obtained through our proposed multi-view, sequence-based optimization method processing data from an 8-camera capture rig. Our dataset comprises 5 hours of recorded interactions from 21 participants captured simultaneously by one head-mounted and seven stationary Kinect cameras, which acquire RGB images and depth maps at 30 Hz. To support future research and benchmarking, we present several baseline models for estimating applied pressure on external surfaces from RGB images, with and without hand pose information. We further explore the joint estimation of the hand mesh and applied pressure. Our experiments demonstrate that pressure and hand pose are complementary for understanding hand-object interactions. ng of hand-object interactions in AR/VR and robotics research. Project page: https://yiming-zhao.github.io/EgoPressure/.

Contact-rich manipulation requires world models to reason over complex contact dynamics from multimodal sensory observations. However, it remains unclear which representation properties fundamentally support stable long-horizon planning in contact-rich settings. In this paper, we present ContactWorld, a benchmark and systematic empirical study of vision-tactile world models spanning 12 contact-rich manipulation tasks, including insertion, disassembly, screwing, and exploratory interaction. Across extensive experiments, we find that representations that are both spatially structured and temporally continuous consistently achieve the strongest planning performance. In particular, point-cloud observations improve average planning success rates from 20.7% with wrist-view observations and 22.0% with front-view observations to 32.1%. We further find that the effectiveness of tactile sensing depends critically on cross-modal representation compatibility rather than modality scaling alone. Combining point-cloud observations with tactile force-field representations, which preserve richer spatial structure and interaction dynamics, further improves performance to 36.1%, yielding the strongest overall planning performance across all evaluated tasks. Moreover, tactile sensing becomes increasingly important under long-horizon planning objectives, where compounding prediction errors and contact uncertainty accumulate over time. Together, these findings highlight the importance of representation structure, multimodal compatibility, and long-horizon robustness in vision-tactile world models for contact-rich robotic manipulation.

Contact-rich manipulation tasks, such as wiping and assembly, require accurate perception of contact forces, friction changes, and state transitions that cannot be reliably inferred from vision alone. Despite growing interest in visuo-tactile manipulation, progress is constrained by two persistent limitations: existing datasets are small in scale and narrow in task coverage, and current methods treat tactile signals as passive observations rather than using them to model contact dynamics or enable closed-loop control explicitly. In this paper, we present OmniViTac, a large-scale visuo-tactile-action dataset comprising 21{,}000+ trajectories across 86 tasks and 100+ objects, organized into six physics-grounded interaction patterns. Building on this dataset, we propose OmniVTA, a world-model-based visuo-tactile manipulation framework that integrates four tightly coupled modules: a self-supervised tactile encoder, a two-stream visuo-tactile world model for predicting short-horizon contact evolution, a contact-aware fusion policy for action generation, and a 60Hz reflexive controller that corrects deviations between predicted and observed tactile signals in a closed loop. Real-robot experiments across all six interaction categories show that OmniVTA outperforms existing methods and generalizes well to unseen objects and geometric configurations, confirming the value of combining predictive contact modeling with high-frequency tactile feedback for contact-rich manipulation. All data, models, and code will be made publicly available on the project website at https://mrsecant.github.io/OmniVTA.

UMI-style interfaces enable scalable robot learning, but existing systems remain largely visuomotor, relying primarily on RGB observations and trajectory while providing only limited access to physical interaction signals. This becomes a fundamental limitation in contact-rich manipulation, where success depends on contact dynamics such as tactile interaction, internal grasping force, and external interaction wrench that are difficult to infer from vision alone. We present OmniUMI, a unified framework for physically grounded robot learning via human-aligned multimodal interaction. OmniUMI synchronously captures RGB, depth, trajectory, tactile sensing, internal grasping force, and external interaction wrench within a compact handheld system, while maintaining collection--deployment consistency through a shared embodiment design. To support human-aligned demonstration, OmniUMI enables natural perception and modulation of internal grasping force, external interaction wrench, and tactile interaction through bilateral gripper feedback and the handheld embodiment. Built on this interface, we extend diffusion policy with visual, tactile, and force-related observations, and deploy the learned policy through impedance-based execution for unified regulation of motion and contact behavior. Experiments demonstrate reliable sensing and strong downstream performance on force-sensitive pick-and-place, interactive surface erasing, and tactile-informed selective release. Overall, OmniUMI combines physically grounded multimodal data acquisition with human-aligned interaction, providing a scalable foundation for learning contact-rich manipulation.

We introduce FEEL (Force-Enhanced Egocentric Learning), the first large-scale dataset pairing force measurements gathered from custom piezoresistive gloves with egocentric video. Our gloves enable scalable data collection, and FEEL contains approximately 3 million force-synchronized frames of natural unscripted manipulation in kitchen environments, with 45% of frames involving hand-object contact. Because force is the underlying cause that drives physical interaction, it is a critical primitive for physical action understanding. We demonstrate the utility of force for physical action understanding through application of FEEL to two families of tasks: (1) contact understanding, where we jointly perform temporal contact segmentation and pixel-level contacted object segmentation; and, (2) action representation learning, where force prediction serves as a self-supervised pretraining objective for video backbones. We achieve state-of-the-art temporal contact segmentation results and competitive pixel-level segmentation results without any need for manual contacted object segmentation annotations. Furthermore we demonstrate that action representation learning with FEEL improves transfer performance on action understanding tasks without any manual labels over EPIC-Kitchens, SomethingSomething-V2, EgoExo4D and Meccano.

The transfer of manipulation skills from human demonstration to robotic execution is often hindered by a "domain gap" in sensing and morphology. This paper introduces MagiClaw, a versatile two-finger end-effector designed to bridge this gap. MagiClaw functions interchangeably as both a handheld tool for intuitive data collection and a robotic end-effector for policy deployment, ensuring hardware consistency and reliability. Each finger incorporates a Soft Polyhedral Network (SPN) with an embedded camera, enabling vision-based estimation of 6-DoF forces and contact deformation. This proprioceptive data is fused with exteroceptive environmental sensing from an integrated iPhone, which provides 6D pose, RGB video, and LiDAR-based depth maps. Through a custom iOS application, MagiClaw streams synchronized, multi-modal data for real-time teleoperation, offline policy learning, and immersive control via mixed-reality interfaces. We demonstrate how this unified system architecture lowers the barrier to collecting high-fidelity, contact-rich datasets and accelerates the development of generalizable manipulation policies. Please refer to the iOS app at https://apps.apple.com/cn/app/magiclaw/id6661033548 for further details.

Learning humanoid loco-manipulation from human demonstrations rests on observing how locomotion, posture, and object interaction evolve together as tasks unfold. Scaling collection across diverse environments, in turn, favors lightweight, portable capture systems. Yet, existing datasets provide only partial views of this coordination. Thus, we introduce EgoExplorer, a 100-hour vision-motion-touch observatory of human loco-manipulation built with a wearable system. With an emphasis on professional activities, its continuous recordings align egocentric video with reconstructed whole-body motion, fine-grained finger articulation, and tactile observations, accompanied by step-level descriptions. To achieve this coverage with sparse body sensing, we develop the Calibrate-Complete-Constrain pipeline. Concretely, reusable calibration fixes participant geometry and sensor attachments before motion inference to disentangle mounting offsets from articulation. A temporal prior then completes unobserved joint motion, while layered constraints promote measurement agreement, temporal continuity, and geometric consistency, properties that motion plausibility alone does not guarantee. Against tracker-fitted references, the method reduces body-point error by 71.9% relative to the strongest baseline; matched evaluations also show gains in hand stability and contact estimation. Preliminary studies explore multimodal generation and conditioning alongside humanoid retargeting with whole-body control in simulation.

Generalist robot policies benefit from large-scale visual pretraining but often struggle with contact-rich dexterous manipulation, where force, compliance, and incipient slip are hard to observe from images. We present Spark-0, a spatially aligned vision-tactile-language-action (VTLA) model that uses touch in two complementary ways. During pretraining, image-space contact maps derived from tactile gloves, together with features from a frozen 3D geometry teacher, supervise the visual tokens; these objectives are removed at inference. In parallel, a tactile pathway encodes regional force histories and 3D taxel states to condition the action expert. A single checkpoint therefore supports both vision-only and tactile-conditioned deployment. To scale this supervision, we build HumanTouch, a 1,000-hour dataset of full-hand tactile human manipulation, and pretrain Spark-0 on it together with egocentric video, robot data, and simulation. We also release SparkArena, which pairs vision-only simulated tasks with tactile-conditioned real-robot tasks on one dexterous embodiment. Spark-0 achieves the highest mean success rate on both SparkArena tracks and ranks first on all eight aggregate metrics of the Ego Humanoid Manipulation Benchmark. Compared with vision-only pretraining on the same data and compute with touch discarded, retaining the touch of 1,000 hours of HumanTouch raises vision-only success on Ego Humanoid from 52.5% to 71.7%, and success on SparkArena-Real, where touch is also used at deployment, from 44.0% to 52.0%, indicating that touch serves not only as a policy input but also as scalable supervision for dexterous visuomotor pretraining. The Website is available at: https://xsparkai.com/Spark-0.

As an essential modality for dexterous and contact-rich tasks, tactile sensing provides precise force feedback that cannot be reliably inferred from vision. However, limited by hardware and data collection systems, existing datasets with tactility remain small in scale and narrow in contact coverage. Meanwhile, Vision-Language-Action (VLA) models with tactile modality are constrained on dynamics-agnostic post-training, which limits the performance ceiling on downstream tasks. In this paper, we present H-Tac, a large-scale tactile-action dataset with 160-hour egocentric human videos containing more than 300 tasks and 135k episodes. Building upon this, we propose Transferable Tactile Pre-Training (TTP), a system of tactile-based pre-training on human data for fine-grained robotic tasks. To bridge the gap between humans and robots, we use unified tactile and action spaces throughout the pre-training and post-training phases, preserving prior knowledge during human-to-robot transfer. By leveraging a tactile expert for future tactile prediction, our framework explicitly models the contact dynamics and precise physical interactions. Extensive experiments in simulation and on real robots demonstrate that our model achieves superior performance, exhibiting robust generalization and fine-grained manipulation capabilities. TTP paves the way for scalable tactile pre-training via human-to-robot transfer.

Touch is fundamental to dexterous manipulation, yet most egocentric human data increasingly used for robot learning lacks tactile information. Directly collecting large-scale tactile data is challenging due to sensor limitations, while human video data is abundant, contact-rich, and easily scalable. This motivates a natural question: can tactile signals be inferred purely from vision? To address this, we introduce EgoTac, a generalizable model that predicts rich tactile information directly from egocentric human videos. EgoTac is trained on a unified corpus of over 5.7M image-tactile pairs, covering both continuous force measurements and binary contacts. By learning from this diverse dataset, EgoTac captures nuanced touch dynamics across varied interactions. Experiments demonstrate strong performance: in-domain prediction achieves an average force error below 0.06N. On out-of-domain contact prediction benchmarks, EgoTac consistently outperforms the state-of-the-art contact estimator. It also captures the rise and fall patterns of real tactile data and enables zero-shot predictions on unconstrained real-world videos. Scaling analyses further reveal that both data diversity and volume improve performance steadily. Overall, EgoTac provides a scalable pathway to extract tactile priors from egocentric human videos, enabling broadly applicable tactile-aware robot learning.

Dexterous manipulation requires tactile feedback. However, robot tactile demonstrations are difficult to scale,because dexterous-hand teleoperation provides limited tactile feedback to the operator. In contrast, human demonstrations offer a substantially more scalable source of diverse tactile interactions. Motivated by a simple premise: hands can change, but the underlying physics of interaction does not. We leverage human tactile data to improve dexterous manipulation policies. Specifically, we first build a tactile motion-capture system that synchronously records images, tactile signals, and hand motions. Using this system, we construct the UVTA dataset spanning five contact-rich tasks, with 1,000 human demonstrations covering diverse interaction patterns and 150 robot demonstrations per task. To transfer the underlying physics of human interaction to robot control, we propose a Unified Visual-Tactile-Action Model that maps both embodiments into aligned tactile and action representations and jointly predicts future action and tactile trajectories. The joint objective enables human demonstrations to supervise contact-aware representation learning, while only robot actions are executed during deployment. In real-robot evaluations across five tasks, our method achieves an average success rate of 70%, outperforming the strongest visual-tactile baseline, which achieves 29%, and an architecture ablation, which achieves 42%. Performance improves consistently with additional human demonstrations and exhibits no saturation at 1,000 demonstrations per task, validating the effectiveness of scalable human tactile data for dexterous manipulation. Project page is available at https://uni-vta.github.io/.

Inference-time steering adapts pre-trained generative robot policies during deployment by verifying candidate actions before execution. While prior methods typically perform this verification only with visual observations, vision alone is often insufficient for contact-rich manipulation, where success depends on both global task progress and subtle local interactions such as contact force. We introduce ViTaL, a visuo-tactile inference-time steering framework that formulates multimodal guidance as a bi-level optimization problem. At the high level, visual sampling-and-verification performs long-horizon mode selection, deciding what behavior the robot should execute. At the low level, tactile-guided diffusion editing refines the selected action sequence over a shorter horizon to satisfy local contact requirements. To support outcome-based steering, ViTaL learns a visuo-tactile latent world model and employs semantically aligned visual and tactile verifiers, including a novel text-conditioned tactile reward that scores predicted tactile futures directly in latent space. Across three real-world contact-rich manipulation tasks, ViTaL improves overall success by 51% over the base policy, outperforms unimodal steering by at least 33%, and exceeds naive multimodal fusion by at least 20%. Website: https://yilin-wu98.github.io/vital_website.

Dexterous manipulation in everyday environments requires both anticipation and reaction: a robot must predict how contact should evolve while rapidly correcting local errors caused by slip, misalignment, unstable grasping, or force mismatch. Vision and language provide semantic and geometric guidance, but they cannot reliably reveal hidden contact states such as force, slip, and contact stability. Although tactile sensing exposes these physical cues, most existing policies treat touch as a low-frequency observation stream within a monolithic action model, coupling slow task reasoning, action generation, and fast contact feedback in a single loop. We introduce TouchWorld, a predictive-and-reactive tactile foundation model for dexterous manipulation. TouchWorld uses a hierarchical policy that separates vision-language subtask planning, tactile world-model prediction, visuo-tactile goal-conditioned action generation, and high-frequency tactile residual refinement. A High-Level Planning Layer produces executable subtasks and predicts tactile subgoals; a Visuo-Tactile Goal-Conditioned Policy generates nominal action chunks; and a Tactile-Conditioned Refinement Policy performs online residual correction using recent tactile and proprioceptive feedback. By using touch as both a predictive contact reference and a fast feedback signal, TouchWorld preserves the semantic generalization of vision-language-action policies while improving local contact adaptation. Across six long-horizon and contact-rich dexterous manipulation tasks, TouchWorld achieves 65.0% success in the clean setting and 53.7% success under human perturbations, outperforming the strongest baseline by 15.7 and 18.5 percentage points, respectively.

Whole-body humanoid manipulation of bulky, deformable, and shared-load objects requires distributed contact sensing and explicit force regulation, yet most imitation policies treat contact force only implicitly. On the other hand, different demonstration sources provide complementary modalities with inherent trade-offs: human demonstrations capture natural contact forces but not robot-executable actions, while teleoperation directly records robot actions but with less natural force regulation. This paper presents WT-UMI, a wearable whole-body tactile interface worn by human operators or mounted on humanoids, providing accurate observations of tactile images, contact forces, and end-effector poses across both human demonstration and humanoid teleoperation modes. We introduce a force-conditioned target-pose correction module that converts measured human poses into contact-aware robot targets by learning corrections from teleoperation data. To leverage the natural force interaction in human data, we propose a force-supervised planner that predicts end-effector pose chunks and contact-force trajectories. The predicted contact force serves as the reference for a tactile-based admittance controller. Across five contact-rich tasks spanning deformable objects, bulky rigid objects, and human--humanoid collaboration, WT-UMI improves success rate and reduces contact-position tracking error over four policy baselines. Our project page is available at https://wt-umi.github.io/WTUMI/.

Touch sensing is beneficial for solving a wide variety of manipulation tasks. While there exists a wide range of tactile sensors with different properties, exploiting the fusion of multiple heterogeneous tactile sensors to improve manipulation learning remains underexplored. We present Multi-Resolution Tactile Sensing (MiTaS), a representation framework that leverages multiple tactile sensors operating at different temporal resolutions in order to solve complex contact-rich manipulation tasks. We propose a novel architecture using modality-specific convolutional stems and transformer-based fusion that effectively fuses information from an RGB camera stream, a vision-based GelSight Mini sensor and a high-frequency event-based Evetac sensor. This multi-sensor representation then conditions a flow-matching policy for solving downstream tasks. Experimental results across five contact-rich manipulation tasks demonstrate the effectiveness of multi-resolution tactile features in imitation learning. MiTaS achieves an average success rate of 80 %, while vision-only (31 %) and visual-tactile (54 %) baselines cannot solve the task reliably. Co-training a visuo-tactile model with multi-tactile data boosts performance by over 10 \% in certain tasks, without having access to the Evetac sensor during policy evaluation. A detailed sensor-reading and attention analysis reveals the importance of different sensors throughout task execution, validating our multi-resolution tactile sensing approach. Project Page: http://mitas-touch.github.io.

Unlike in language or vision, one of the fundamental challenges in robot learning is the lack of access to vast data resources. We can further break down the problem into (1) data sparsity from the angle of data representation and (2) data scarcity from the angle of data quantity. In this thesis, I will discuss selected works on two domains: (1) tactile sensing and (2) rehabilitation robots, which are exemplars of data sparsity and scarcity, respectively. Tactile sensing is an essential modality for robotics, but tactile data are often sparse, and for each interaction with the physical world, tactile sensors can only obtain information about the local area of contact. I will discuss my work on learning vision-free tactile-only exploration and manipulation policies through model-free reinforcement learning to make efficient use of sparse tactile information. On the other hand, rehabilitation robots are an example of data scarcity to the extreme due to the significant challenge of collecting biosignals from disabled-bodied subjects at scale for training. I will discuss my work in collaboration with the medical school and clinicians on intent inferral for stroke survivors, where a hand orthosis developed in our lab collects a set of biosignals from the patient and uses them to infer the activity that the patient intends to perform, so the orthosis can provide the right type of physical assistance at the right moment. My work develops machine learning algorithms that enable intent inferral with minimal data, including semi-supervised, meta-learning, and generative AI methods.

Handheld data collection systems, such as the Universal Manipulation Interface (UMI), enable scalable data collection across diverse environments but only capture observed actions rather than the desired actions executed by a robot controller. In contrast, teleoperation captures desired actions directly, but is prohibitively time-consuming to collect. We revisit this trade-off through the lens of action validity across task phases. We observe that handheld trajectories provide valid supervision in tolerant, free-space phases, but lack dynamic feasibility in contact-sensitive phases, where tracking observed trajectories at high stiffness produces large, unsafe contact forces. We study the interaction between these two supervision types for contact-rich manipulation and find that training policies that combine handheld data with a small number of targeted teleoperated demonstrations provide an efficient hybrid strategy. Specifically, rather than teleoperating the entire task, we only collect partial teleoperated demonstrations for task segments where base handheld policies fail. However, naively mixing handheld and teleoperated phase-specific data yields worse performance than training on handheld data alone. To address this mismatch between observed and desired supervision, we propose Bi-modal Routing for Imitation Data via Gated Experts (BRIDGE), a mixture of diffusion policy experts that routes between specialist task phase heads conditioned on the current robot state. Notably, our approach enables task-phase specific use of desired actions during contact sensitive segments and improves success rates over handheld-only baselines by up to 36.7% across three contact-rich manipulation tasks.

Vision-based tactile sensing is widely used in perception, reconstruction, and robotic manipulation, yet collecting large-scale tactile data remains costly due to diverse sensor-object interactions and inconsistencies across sensor instances. Existing approaches to scaling tactile data---simulation and free-form tactile generation---often yield unrealistically rendered signals with poor transfer to highly dynamic real-world tasks. We propose \name, a two-stage controllable tactile image generation framework that generates realistic tactile images conditioned on a single reference tactile image, contact force, and contact pose. By grounding generation in these important physical priors, \name synthesizes realistic samples across different sensors while effectively capturing task-relevant variations. Across a series of downstream tasks and real-world experiments, such as object insertion, imitation learning, and object weighting, the augmented datasets using our approach consistently improve performance and demonstrate practical utility in dynamic real-world settings. Project page: https://dongyuluo.github.io/controltac.

Every robot already carries high-resolution contact sensors: its own joints. Legged robots and humanoids exploit them to walk, run, and track whole-body motions without vision, but there the contacts are large and forceful. Is joint sensing also enough for precise, contact-rich assembly, where the robot must find a millimeter-scale opening, mesh gear teeth, or catch a thread through light contact? We study this question by training blind assembly policies that observe only a short history of joint positions, velocities, and their own actions, without visual, force, torque, or tactile sensing. The poses of both the fixture and the part are unknown to the policy, and the grasp is randomized substantially. The policy must therefore assemble the parts through contact, sensed exclusively through its own proprioception. Trained with reinforcement learning entirely in simulation over randomized parts, grasps, and contacts, such policies learn peg insertion, gear meshing, and nut threading. The peg insertion policy transfers zero-shot to the real world and inserts pegs of different shapes and sizes in 73% of trials. Controlled comparisons with matched visual policies in simulation show that blind policies generalize far better to unseen part shapes and sizes, though they can be slower. Training such policies needs thousands of different assemblies, each simulated with its clearance intact, so we also release an open-source generator that builds them procedurally from exact convex pieces for MuJoCo; it is more accurate and faster than convex decomposition or MuJoCo's signed-distance collision. Videos and interactive simulations are at https://younghyopark.me/blind-proprioceptive-assembly/.

Humanoid robots promise general-purpose assistance, yet real-world humanoid loco-manipulation remains challenging because it requires whole-body stability, dexterous hands, and contact-aware perception under frequent contact changes. In this work, we study dexterous, contact-rich humanoid loco-manipulation. We first develop an RL-based whole-body controller that provides stable lower-body and torso execution during complex manipulation. Built on this controller, we develop a whole-body humanoid data collection system that combines VR-based teleoperation with human-to-humanoid motion mapping, enabling efficient collection of real-world demonstrations. We then propose Humanoid Transformer with Touch Dreaming (HTD), a multimodal encoder--decoder Transformer that models touch as a core modality alongside multi-view vision and proprioception. HTD is trained in a single stage with behavioral cloning augmented by touch dreaming: in addition to predicting action chunks, the policy predicts future hand-joint forces and future tactile latents, encouraging the shared Transformer trunk to learn contact-aware representations for dexterous interaction. Across five contact-rich tasks, Insert-T, Book Organization, Towel Folding, Cat Litter Scooping, and Tea Serving, HTD achieves a 90.9% relative improvement in average success rate over the stronger baseline. Ablation results further show that latent-space tactile prediction is more effective than raw tactile prediction, yielding a 30% relative gain in success rate. These results demonstrate that combining robust whole-body execution, scalable humanoid data collection, and predictive touch-centered learning enables versatile, high-dexterity humanoid manipulation in the real world. Project webpage: humanoid-touch-dream.github.io.

Large-scale, high-quality multimodal demonstrations are essential for robot learning of contact-rich dexterous manipulation. While human-centric data collection systems lower the barrier to scaling, they struggle to capture the tactile information during physical interactions. Motivated by this, we present DexViTac, a portable, human-centric data collection system tailored for contact-rich dexterous manipulation. The system enables the high-fidelity acquisition of first-person vision, high-density tactile sensing, end-effector poses, and hand kinematics within unstructured, in-the-wild environments. Building upon this hardware, we propose a kinematics-grounded tactile representation learning algorithm that effectively resolves semantic ambiguities within tactile signals. Leveraging the efficiency of DexViTac, we construct a multimodal dataset comprising over 2,400 visuo-tactile-kinematic demonstrations. Experiments demonstrate that DexViTac achieves a collection efficiency exceeding 248 demonstrations per hour and remains robust against complex visual occlusions. Real-world deployment confirms that policies trained with the proposed dataset and learning strategy achieve an average success rate exceeding 85% across four challenging tasks. This performance significantly outperforms baseline methods, thereby validating the substantial improvement the system provides for learning contact-rich dexterous manipulation. Project page: https://xitong-c.github.io/DexViTac/.

Contact-rich manipulation depends on applying the correct grasp forces throughout the manipulation task, especially when handling fragile or deformable objects. Most existing imitation learning approaches often treat visuotactile feedback only as an additional observation, leaving applied forces as an uncontrolled consequence of gripper commands. In this work, we present Force-Aware Robotic Manipulation (FARM), an imitation learning framework that integrates high-dimensional tactile data to infer tactile-conditioned force signals, which in turn define a matching force-based action space. We collect human demonstrations using a modified version of the handheld Universal Manipulation Interface (UMI) gripper that integrates a GelSight Mini visual tactile sensor. For deploying the learned policies, we developed an actuated variant of the UMI gripper with geometry matching our handheld version. During policy rollouts, the proposed FARM diffusion policy jointly predicts robot pose, grip width, and grip force. FARM outperforms several baselines across three tasks with distinct force requirements -- high-force, low-force, and dynamic force adaptation -- demonstrating the advantages of its two key components: leveraging force-grounded, high-dimensional tactile observations and a force-based control space. The codebase and design files are open-sourced and available at https://tactile-farm.github.io .

Tactile sensing is a crucial capability for Vision-Language-Action (VLA) architectures, as it enables dexterous and safe manipulation in contact-rich tasks. However, reliance on dedicated tactile hardware increases cost and reduces reproducibility across robotic platforms. We argue that tactile-aware manipulation can be learned offline and deployed without direct haptic feedback at inference. To this end, we present HapticVLA, which proceeds in two tightly coupled stages: Safety-Aware Reward-Weighted Flow Matching (SA-RWFM) and Tactile Distillation (TD). SA-RWFM trains a flow-matching action expert that incorporates precomputed, safety-aware tactile rewards penalizing excessive grasping force and suboptimal grasping trajectories. TD further transfers this tactile-aware capability into a conventional VLA: we distill a compact tactile token from the SA-RWFM teacher and train a student VLA to predict that token from vision and state modalities, enabling tactile-aware action generation at inference without requiring on-board tactile sensors. This design preserves contact-rich tactile-aware reasoning within VLA while removing the need for on-board tactile sensors during deployment. On real-world experiments, HapticVLA achieves a mean success rate of 86.7%, consistently outperforming baseline VLAs - including versions provided with direct tactile feedback during inference.

Contact-rich manipulation requires policies to react to local deformation, pressure, slip, and friction, yet these cues are temporally sparse and often invisible in visual observations. Existing visual-tactile policies usually feed tactile observations directly into action prediction, but rarely model tactile deformation dynamics during action generation. In this paper, we introduce VT-WAM, a Visual-Tactile World Action Model that jointly learns future visual prediction, tactile deformation prediction, and action prediction within a unified flow matching framework. In particular, VT-WAM introduces (1) Asymmetric Mixture-of-Transformers (MoT) attention to bridge a first-frame visual anchor with temporal tactile dynamics, and (2) contact-gated Action-Visual-Tactile Attention Guidance (AVTAG) to encourage action queries to rely on tactile evidence during contact phases. Across six real-world contact-rich manipulation tasks, VT-WAM achieves a 71.67% average success rate, outperforming Fast-WAM by 26.67% and OmniVTLA by 35.84%. Ablations demonstrate that modeling tactile deformation dynamics and guiding contact-phase tactile attention are both important for contact-rich tasks. Project website: https://vt-wam.github.io/.

Robotic manipulation integrates vision, touch, and language, whose importance shifts across stages: vision guides reaching, while touch, through its evolution over time, decides grasping, alignment, and contact. Yet existing multi-modal manipulation policies typically use fixed temporal contexts and fusion strategies, despite shifts in what each modality contributes across different skills. We study how vision and touch should be combined at the level of primitive skills, asking what each skill needs from each sensor, and propose a skill-conditioned representation in which the queried skill conditions fusion over modality-specific short-term observation tokens while attending to a sparse event memory that retains terminal observations from the last K executed skills. Evaluated by skill progress estimation on three contact-rich tasks, it reduces slip-detection delay by 87% against fine-tuned SOTA progress models, twist-completion delay by 67.5% against a vision-only ablation, and progress error on a blind search task by 92% through sparse event memory. Gains concentrate exactly where completion is defined by contact or task history. More broadly, our results suggest that observation formation not only policy architecture is a central challenge in multi-modal representation. Project Website: http://what-to-attend-what-to-keep.github.io/

Teleoperation of robotic systems for precise and delicate object grasping requires high-fidelity haptic feedback to obtain comprehensive real-time information about the grasp. In such cases, the most common approach is to use kinesthetic feedback. However, a single contact point information is insufficient to detect the dynamically changing shape of soft objects. This paper proposes a novel telemanipulation system that provides kinesthetic and cutaneous stimuli to the user's hand to achieve accurate liquid dispensing by dexterously manipulating the deformable object (i.e., pipette). The experimental results revealed that the proposed approach to provide the user with multimodal haptic feedback considerably improves the quality of dosing with a remote pipette. Compared with pure visual feedback, the relative dosing error decreased by 66\% and task execution time decreased by 18\% when users manipulated the deformable pipette with a multimodal haptic interface in combination with visual feedback. The proposed technology can be potentially implemented in delicate dosing procedures during the antibody tests for COVID-19, chemical experiments, operation with organic materials, and telesurgery.

Contact often occurs without macroscopic surface deformation, such as during interaction with liquids, semi-liquids, or ultra-soft materials. However, most existing tactile sensors rely on deformation to infer contact, making such light-contact interactions difficult to perceive robustly. To address this, we present LightTact, a visual-tactile fingertip sensor that makes contact directly visible via a deformation-independent principle. LightTact features an ambient-blocking optical configuration that suppresses both external light and internal illumination at non-contact regions, while transmitting only the scattered light generated at true contacts. As a result, LightTact produces high-contrast raw images in which non-contact pixels remain near-black (mean gray value < 3) and contact pixels preserve the natural appearance of the contacting surface. Built on this, LightTact achieves accurate pixel-level contact segmentation that is robust to material properties, contact force, surface appearance, and environmental lighting. We further demonstrate that LightTact unlocks new robotic manipulation behaviors that require detection of extremely light contact, including water spreading, facial-cream dipping, and soft thin-film interaction. In addition, we show that LightTact's spatially aligned visual-tactile images can be directly interpreted by vision-language models.

Tactile sensing plays a vital role in enabling robots to perform fine-grained, contact-rich tasks. However, the high dimensionality of tactile data, due to the large coverage on dexterous hands, poses significant challenges for effective tactile feature learning, especially for 3D tactile data, as there are no large standardized datasets and no strong pretrained backbones. To address these challenges, we propose a novel canonical representation that reduces the difficulty of 3D tactile feature learning and further introduces a force-based self-supervised pretraining task to capture both local and net force features, which are crucial for dexterous manipulation. Our method achieves an average success rate of 78% across four fine-grained, contact-rich dexterous manipulation tasks in real-world experiments, demonstrating effectiveness and robustness compared to other methods. Further analysis shows that our method fully utilizes both spatial and force information from 3D tactile data to accomplish the tasks. The codes and videos can be viewed at https://3dtacdex.github.io.

Vision-Language-Action (VLA) models have advanced robotic manipulation by combining vision, language, and proprioception to predict actions. However, previous methods fuse proprioceptive signals directly with VLM-encoded vision-language features, resulting in state-dominant bias and false completions despite visible execution failures. We attribute this to modality imbalance, where policies over-rely on internal state while underusing visual evidence. To address this, we present ReViP, a novel VLA framework with Vision-Proprioception Rebalance to enhance visual grounding and robustness under perturbations. The key insight is to introduce auxiliary task-aware environment priors to adaptively modulate the coupling between semantic perception and proprioceptive dynamics. Specifically, we use an external VLM as a task-stage observer to extract real-time task-centric visual cues from visual observations, which drive a Vision-Proprioception Feature-wise Linear Modulation to enhance environmental awareness and reduce state-driven errors. Moreover, to evaluate false completion, we propose the first False-Completion Benchmark Suite built on LIBERO with controlled settings such as Object-Drop. Extensive experiments show that ReViP effectively reduces false-completion rates and improves success rates over strong VLA baselines on our suite, with gains extending to LIBERO, RoboTwin 2.0, and real-world evaluations.

In this paper, we address force-aware control and force distribution in robotic platforms with multi-fingered hands. Given a target goal and force estimates from tactile sensors, we design a controller that adapts the motion of the torso, arm, wrist, and fingers, redistributing forces to maintain stable contact with objects of varying mass distribution or unstable contacts. To estimate forces, we collect a dataset of tactile signals and ground-truth force measurements using five Xela magnetic sensors interacting with indenters, and train force estimators. We then introduce a model-based control scheme that minimizes the distance between the Center of Pressure (CoP) and the centroid of the fingertips contact polygon. Since our method relies on estimated forces rather than raw tactile signals, it has the potential to be applied to any sensor capable of force estimation. We validate our framework on a balancing task with five objects, achieving a 82.7% success rate, and further evaluate it in multi-object scenarios, achieving 80% accuracy. Code and data can be found here https://github.com/hsp-iit/multifingered-force-aware-control.

Many everyday tasks require controlling contact force as well as motion. On a humanoid, this force must often be coordinated across both hands and the whole body, and cannot be specified by kinematic trajectories alone. Therefore, we present FLORE, a framework for learning force-reactive humanoid loco-manipulation. We collect robot-free demonstrations using two force-sensing UMI-style handheld grippers for hand motion and contact wrenches, and wearable trackers for body motion. A force-reactive diffusion policy takes vision, proprioception, and measured wrenches as input, then predicts actions and per-hand force commands. A hybrid compliance whole-body controller with force tracking executes these commands while maintaining balance: an integral of the force error measured by real force/torque (F/T) sensors lets each hand track force accurately along the commanded direction and remain compliant along the others. In simulation, the controller tracks per-hand force commands of varied magnitude and direction, with little loss in whole-body motion accuracy. Across three contact-rich tasks on the robot, the force-reactive policy succeeds in 80% of rollouts, compared with 26.7% for a position-only policy trained on the same demonstrations and executed by the same controller. For more details, please visit our website: https://louis-leee.github.io/FLoRe/.

Tactile sensing is one of the modalities humans rely on heavily to perceive the world. Working with vision, this modality refines local geometry structure, measures deformation at the contact area, and indicates the hand-object contact state. With the availability of open-source tactile sensors such as DIGIT, research on visual-tactile learning is becoming more accessible and reproducible. Leveraging this tactile sensor, we propose a novel visual-tactile in-hand object reconstruction framework VTacO, and extend it to VTacOH for hand-object reconstruction. Since our method can support both rigid and deformable object reconstruction, no existing benchmarks are proper for the goal. We propose a simulation environment, VT-Sim, which supports generating hand-object interaction for both rigid and deformable objects. With VT-Sim, we generate a large-scale training dataset and evaluate our method on it. Extensive experiments demonstrate that our proposed method can outperform the previous baseline methods qualitatively and quantitatively. Finally, we directly apply our model trained in simulation to various real-world test cases, which display qualitative results. Codes, models, simulation environment, and datasets are available at https://sites.google.com/view/vtaco/.

Tactile sensing provides essential contact information for robotic manipulation, yet incorporating it into pretrained vision-language-action (VLA) models remains challenging. A common concern is that simply introducing touch during task-specific fine-tuning may fail to bridge the cross-modal gap, yielding limited gains or even reduced success. Consequently, existing methods often rely on large-scale tactile policy pretraining or separate visuotactile alignment, adding data requirements and training stages. We introduce SimpleTouch, a simple VLA extension that augments π_{0.5} with a tactile expert, to test whether these additional stages are necessary. Leveraging all tokens from a frozen pretrained tactile encoder, the expert learns from action supervision and multi-horizon prediction of future tactile latents. This single-stage training uses only task demonstrations, without additional tactile policy pretraining or separate alignment. With 50 demonstrations per task, SimpleTouch achieves the highest success rate among evaluated methods on all six UniVTAC tasks. Its average success rate reaches 77.5%, compared with 45.2% for FTP-π_{0.5} and 66.7% for FTP-1, corresponding to gains of 32.3 and 10.8 percentage points, respectively. Across four real-world tasks, it averages 71.3%, exceeding FTP-1 by 8.8 percentage points. These results demonstrate that, given pretrained VLA and tactile representations, additional tactile policy pretraining is not a prerequisite for strong performance on these tasks, offering a simpler route to contact-rich manipulation. Project page: https://simpletouch-robot.github.io/

Human demonstrations offer an efficient and scalable source of data for dexterous robot manipulation, but differences in sensing and hand morphology complicate the transfer of contact-rich interactions. We present TouchBridge, a hardware--software co-designed framework for human-to-robot data transformation. A wearable human demonstration interface and a corresponding robot interface establish cross-embodiment correspondence in visual and fingertip tactile sensing. We introduce Tac-Retarget, a tactile-conditioned retargeting method that uses measured contact to align fingertip contact patches and preserve their spatial relations within and across hands. Unlike object-aware or simulation-based transfer pipelines, Tac-Retarget requires no object mesh, object-pose estimate, or physics simulation for retargeting, enabling direct and scalable conversion of human demonstrations into robot-domain training data. Combined with visual synthesis and camera-anchored action conversion, TouchBridge produces robot-domain demonstrations for fine-tuning a pretrained vision-language-action (VLA) model. Across four real-world contact-rich tasks, policies fine-tuned solely on TouchBridge-converted human demonstrations achieve a 72.5% average success rate, compared with 77.5% using an equal number of teleoperated robot demonstrations, while human demonstration collection is 7.0x faster. Under the same policy and training setup, Tac-Retarget outperforms DexPilot and UniDex by 25.0 and 42.5 percentage points, respectively.

Teleoperation is a key approach for collecting high-quality, physically consistent demonstrations for robotic manipulation. However, teleoperation for dexterous manipulation remains constrained by: (i) inaccurate hand-robot motion mapping, which limits teleoperated dexterity, and (ii) limited tactile feedback that forces vision-dominated interaction and hinders perception of contact geometry and force variation. To address these challenges, we present TAG, a low-cost glove system that integrates precise hand motion capture with high-resolution tactile feedback, enabling effective tactile-in-the-loop dexterous teleoperation. For motion capture, TAG employs a non-contact magnetic sensing design that provides drift-free, electromagnetically robust 21-DoF joint tracking with joint angle estimation errors below 1 degree. Meanwhile, to restore tactile sensation, TAG equips each finger with a 32-actuator tactile array within a compact 2 cm^2 module, allowing operators to directly feel physical interactions at the robot end-effector through spatial activation patterns. Through real-world teleoperation experiments and user studies, we show that TAG enables reliable real-time perception of contact geometry and dynamic force, improves success rates in contact-rich teleoperation tasks, and increases the reliability of demonstration data collection for learning-based manipulation.

Contact-rich manipulation is central to many everyday human activities, requiring continuous adaptation to contact uncertainty and external disturbances through multi-modal perception, particularly vision and tactile feedback. While imitation learning has shown strong potential for learning complex manipulation behaviors, most existing approaches rely on action chunking, which fundamentally limits their ability to react to unforeseen observations during execution. This limitation becomes especially critical in contact-rich scenarios, where physical uncertainty and high-frequency tactile feedback demand rapid, reactive control. To address this challenge, we propose Tube Diffusion Policy (TDP), a novel reactive visual-tactile policy learning framework that bridges diffusion-based imitation learning with tube-based feedback control. By leveraging the expressive power of generative models, TDP learns an observation-conditioned feedback flow around nominal action chunks, forming an action tube that enables fast and adaptive reactions during execution. We evaluate TDP on the widely used Push-T benchmark and three additional challenging visual-tactile dexterous manipulation tasks. Across all benchmarks, TDP consistently outperforms state-of-the-art imitation learning baselines. Two real-world experiments further validate its robust reactivity under contact uncertainty and external disturbances. Moreover, the step-wise correction mechanism enabled by action tube significantly reduces the required denoising steps, making TDP well suited for real-time, high-frequency feedback control in contact-rich manipulation.

While rule-based reinforcement learning has recently catalyzed explicit reasoning in multimodal models, tactile reasoning remains largely underexplored. Existing tactile-language models primarily rely on supervised or contrastive objectives, which limits their capacity to ground predictions in physical evidence or rectify misleading visual priors. Tactile reasoning introduces two modality-specific challenges: the ordinal nature of physical attributes (e.g., hardness, roughness) and the cross-sensor distribution shifts inherent in optical tactile hardware. In this work, we introduce TouchReason-1M, a large-scale multimodal dataset comprising over 1M synchronized tactile pairs across four distinct sensors, and TouchReason-Bench, a rigorous framework for evaluating tactile perception and visual-tactile conflict resolution. Building upon these, we propose Touch-R1, a tactile reasoning MLLM based on Qwen2.5-VL-7B. Touch-R1 is trained via a tactile-grounded GRPO objective that combines ordinal-aware accuracy, cross-sensor physical consistency, structured-format control, and an input-side tactile grounding objective. Specifically, the tactile-use reward assigns credit only when authentic tactile inputs yield superior correctness relative to counterfactual controls where the tactile stream is removed, shuffled, or noise-masked. On TouchReason-Bench, Touch-R1-7B outperforms Octopi-13B by 18.4\% and GPT-4o by 24.7\% on average. Its structured reasoning traces reveal emergent behaviors of probing, comparison, and revision, demonstrating that R1-style reasoning can be effectively grounded in physical contact.

Long-horizon humanoid vision--language--action (VLA) control with head-mounted stereo cameras requires visual interfaces that can exploit complementary views while maintaining compatibility with pretrained representations. Existing interfaces often discard complementary stereo evidence or fuse additional observations without preserving the native primary-view pathway and adapting auxiliary information to robot embodiment. We present EATR-Stereo, an embodiment-aware token-routing framework that retains primary-view tokens and constructs primary-aligned Cross-View Auxiliary Tokens (CVATs) by querying the synchronized auxiliary-view token sequence. A body-segmented proprioceptive encoder further conditions token-wise auxiliary usage on robot configuration history, enabling selective incorporation of stereo evidence during action generation. The routed auxiliary stream augments the language and primary-visual context of a pretrained VLA while keeping its vision--language model frozen. On a 33-DoF physical humanoid with a 37-D proprioceptive state, we evaluate nine configurations in over-100-s search--approach--grasp--place--return tasks. EATR-Stereo achieves 60.0% full-task success, 100.0% grasp success, and 80.0% stage success. Under severe asymmetric occlusion, it improves recovery to 80% compared with 30% for CVAT alone. Ablation studies further show the importance of preserving primary tokens and combining cross-view auxiliary features with structured proprioceptive routing. These results demonstrate that selectively routed paired stereo evidence improves spatial grounding for reliable long-horizon humanoid VLA control.

Modern video generative models produce visually impressive results, yet frequently violate basic physical principles. We propose Proprio, a training-free framework that enables a frozen video generator to assess and improve the physical plausibility of its own outputs. Inspired by proprioception, the biological sense of one's own movement, Proprio treats the model's flow residual under controlled latent perturbations as a self-scoring signal. Samples that are better explained by the generator's learned dynamics induce smaller and more stable residuals. We aggregate this signal across timesteps and perturbations, focus it on motion-relevant regions with a dynamic spatiotemporal mask, and use it for best-of-N search, gradient-based self-refinement, or both. Across text-to-video and image-to-video benchmarks, Proprio consistently improves physical plausibility, outperforming VLM-based scoring, and external world-model baselines in several settings. With TurboWan2.2, Proprio improves Physics-IQ from 32.2 to 37.5 (+16.5%) and VideoPhy2-hard physical commonsense from 45.6 to 55.0 (+20.6%). Human evaluation further shows that raters prefer Proprio-selected or refined videos for physical plausibility in roughly two-thirds of comparisons. These results suggest that frozen video generators contain actionable internal signals for evaluating and improving the physical plausibility of their own outputs.

Tactile perception has the potential to significantly enhance dexterous robotic manipulation by providing rich local information that can complement or substitute for other sensory modalities such as vision. However, because tactile sensing is inherently local, it is not well-suited for tasks that require broad spatial awareness or global scene understanding on its own. A human-inspired strategy to address this issue is to consider active perception techniques instead. That is, to actively guide sensors toward regions with more informative or significant features and integrate such information over time in order to understand a scene or complete a task. Both active perception and different methods for tactile sensing have received significant attention recently. Yet, despite advancements, both fields lack standardized benchmarks. To bridge this gap, we introduce the Tactile MNIST Benchmark Suite, an open-source, Gymnasium-compatible benchmark specifically designed for active tactile perception tasks, including localization, classification, and volume estimation. Our benchmark suite offers diverse simulation scenarios, from simple toy environments all the way to complex tactile perception tasks using vision-based tactile sensors. Furthermore, we also offer a comprehensive dataset comprising 13,500 synthetic 3D MNIST digit models and 153,600 real-world tactile samples collected from 600 3D printed digits. Using this dataset, we train a CycleGAN for realistic tactile simulation rendering. By providing standardized protocols and reproducible evaluation frameworks, our benchmark suite facilitates systematic progress in the fields of tactile sensing and active perception.

Real-world contact-rich manipulation demands robots to perceive temporal tactile feedback, capture subtle surface deformations, and reason about object properties as well as force dynamics. Although optical tactile sensors are uniquely capable of providing such rich information, existing tactile datasets and models remain limited. These resources primarily focus on object-level attributes (e.g., material) while largely overlooking fine-grained tactile temporal dynamics during physical interactions. We consider that advancing dynamic tactile perception requires a systematic hierarchy of dynamic perception capabilities to guide both data collection and model design. To address the lack of tactile data with rich dynamic information, we present ToucHD, a large-scale hierarchical tactile dataset spanning tactile atomic actions, real-world manipulations, and touch-force paired data. Beyond scale, ToucHD establishes a comprehensive tactile dynamic data ecosystem that explicitly supports hierarchical perception capabilities from the data perspective. Building on it, we propose AnyTouch 2, a general tactile representation learning framework for diverse optical tactile sensors that unifies object-level understanding with fine-grained, force-aware dynamic perception. The framework captures both pixel-level and action-specific deformations across frames, while explicitly modeling physical force dynamics, thereby learning multi-level dynamic perception capabilities from the model perspective. We evaluate our model on benchmarks that covers static object properties and dynamic physical attributes, as well as real-world manipulation tasks spanning multiple tiers of dynamic perception capabilities-from basic object-level understanding to force-aware dexterous manipulation. Experimental results demonstrate consistent and strong performance across sensors and tasks.

Tactile perception is a critical component of solving real-world manipulation tasks, but tactile sensors for manipulation have barriers to use such as fragility and cost. In this work, we engage a robust, low-cost tactile sensor, BeadSight, as an alternative to precise pre-calibrated sensors for a pretraining approach to manipulation. We show that tactile pretraining, even with a low-fidelity sensor as BeadSight, can improve an imitation learning agent's performance on complex manipulation tasks. We demonstrate this method against a baseline USB cable plugging task, previously achieved with a much higher precision GelSight sensor as the tactile input to pretraining. Our best BeadSight pretrained visuo-tactile agent completed the task with 70\% accuracy compared to 85\% for the best GelSight pretrained visuo-tactile agent, with vision-only inference for both.

In robotic manipulation, tactile sensors are indispensable, especially when dealing with soft objects, objects of varying dimensions, or those out of the robot's direct line of sight. Traditional tactile sensors often grapple with challenges related to cost and durability. To address these issues, our study introduces a novel approach to visuo-tactile sensing with an emphasis on economy and replacablity. Our proposed sensor, BeadSight, uses hydro-gel beads encased in a vinyl bag as an economical, easily replaceable sensing medium. When the sensor makes contact with a surface, the deformation of the hydrogel beads is observed using a rear camera. This observation is then passed through a U-net Neural Network to predict the forces acting on the surface of the bead bag, in the form of a pressure map. Our results show that the sensor can accurately predict these pressure maps, detecting the location and magnitude of forces applied to the surface. These abilities make BeadSight an effective, inexpensive, and easily replaceable tactile sensor, ideal for many robotics applications.

Handheld paradigms offer an efficient and intuitive way for collecting large-scale demonstration of robot manipulation. However, achieving contact-rich bimanual manipulation through these methods remains a pivotal challenge, which is substantially hindered by hardware adaptability and data efficacy. Prior hardware designs remain gripper-specific and often face a trade-off between tracking precision and portability. Furthermore, the lack of online feasibility checking during demonstration leads to poor replayability. More importantly, existing handheld setups struggle to collect interactive recovery data during robot execution, lacking the authentic tactile information necessary for robust policy refinement. To bridge these gaps, we present TAMEn, a tactile-aware manipulation engine for closed-loop data collection in contact-rich tasks. Our system features a cross-morphology wearable interface that enables rapid adaptation across heterogeneous grippers. To balance data quality and environmental diversity, we implement a dual-modal acquisition pipeline: a precision mode leveraging motion capture for high-fidelity demonstrations, and a portable mode utilizing VR-based tracking for in-the-wild acquisition and tactile-visualized recovery teleoperation. Building on this hardware, we unify large-scale tactile pretraining, task-specific bimanual demonstrations, and human-in-the-loop recovery data into a pyramid-structured data regime, enabling closed-loop policy refinement. Experiments show that our feasibility-aware pipeline significantly improves demonstration replayability, and that the proposed visuo-tactile learning framework increases task success rates from 34% to 75% across diverse bimanual manipulation tasks. We further open-source the hardware and dataset to facilitate reproducibility and support research in visuo-tactile manipulation.

Physical interaction quality is central to deformable-object manipulation, yet most benchmarks evaluate task success alone. A policy may complete the task while allowing slip or causing excessive compression. A primary bottleneck is the absence of visuo-tactile datasets that pair policy-visible contact observations with independent physical ground truth over complete tasks. We introduce SoftVTBench, a visuo-tactile dataset for physical-interaction-aware deformable-object manipulation. It contains 4,000 expert demonstrations and more than 50 assets, including volumetric deformable objects and visually matched rigid twins. At 20 Hz, each episode synchronizes multi-view RGB, dual-finger tactile RGB and marker motion, proprioception, language, and binary and continuous gripper actions, alongside evaluator-only finite-element (FEM) states. Building upon this dataset, we establish a closed-loop benchmark that uses fixed object-specific calibration to define the Deformation-aware Success Rate (DSR), which counts a rollout as successful only when it completes the task and keeps peak normalized deformation within tolerance. Across Diffusion Policy, π_{0.5}, and FastWAM, all 12 in-distribution configurations contain successful rollouts that violate the deformation tolerance, accounting for 0.7--24% of each configuration's successes. Under distribution shift, visuo-tactile variants achieve higher task success in all six policy--suite comparisons and higher DSR in five, whereas their in-distribution benefits are mixed. These results show that making touch available does not by itself ensure effective multimodal fusion. SoftVTBench therefore provides a common visuo-tactile resource for studying not only whether a policy succeeds, but how it physically interacts with deformable objects and when touch improves that interaction.

Vision-Language-Action (VLA) models have advanced general-purpose robotic manipulation by leveraging pretrained visual and linguistic representations. However, they struggle with contact-rich tasks that require fine-grained control involving force, especially under visual occlusion or dynamic uncertainty. To address these limitations, we propose ForceVLA, a novel end-to-end manipulation framework that treats external force sensing as a first-class modality within VLA systems. ForceVLA introduces FVLMoE, a force-aware Mixture-of-Experts fusion module that dynamically integrates pretrained visual-language embeddings with real-time 6-axis force feedback during action decoding. This enables context-aware routing across modality-specific experts, enhancing the robot's ability to adapt to subtle contact dynamics. We also introduce ForceVLA-Data, a new dataset comprising synchronized vision, proprioception, and force-torque signals across five contact-rich manipulation tasks. ForceVLA improves average task success by 23.2\% over strong pi_0-based baselines, achieving up to 80\% success in tasks such as plug insertion. Our approach highlights the importance of multimodal integration for dexterous manipulation and sets a new benchmark for physically intelligent robotic control. Code and data will be released at https://sites.google.com/view/forcevla2025.

Humans can accomplish complex contact-rich tasks using vision and touch, with highly reactive capabilities such as quick adjustments to environmental changes and adaptive control of contact forces; however, this remains challenging for robots. Existing visual imitation learning (IL) approaches rely on action chunking to model complex behaviors, which lacks the ability to respond instantly to real-time tactile feedback during the chunk execution. Furthermore, most teleoperation systems struggle to provide fine-grained tactile / force feedback, which limits the range of tasks that can be performed. To address these challenges, we introduce TactAR, a low-cost teleoperation system that provides real-time tactile feedback through Augmented Reality (AR), along with Reactive Diffusion Policy (RDP), a novel slow-fast visual-tactile imitation learning algorithm for learning contact-rich manipulation skills. RDP employs a two-level hierarchy: (1) a slow latent diffusion policy for predicting high-level action chunks in latent space at low frequency, (2) a fast asymmetric tokenizer for closed-loop tactile feedback control at high frequency. This design enables both complex trajectory modeling and quick reactive behavior within a unified framework. Through extensive evaluation across three challenging contact-rich tasks, RDP significantly improves performance compared to state-of-the-art visual IL baselines through rapid response to tactile / force feedback. Furthermore, experiments show that RDP is applicable across different tactile / force sensors. Code and videos are available on https://reactive-diffusion-policy.github.io.

Imitation learning requires high-quality demonstrations consisting of sequences of state-action pairs. For contact-rich dexterous manipulation tasks that require dexterity, the actions in these state-action pairs must produce the right forces. Current widely-used methods for collecting dexterous manipulation demonstrations are difficult to use for demonstrating contact-rich tasks due to unintuitive human-to-robot motion retargeting and the lack of direct haptic feedback. Motivated by these concerns, we propose DexForce. DexForce leverages contact forces, measured during kinesthetic demonstrations, to compute force-informed actions for policy learning. We collect demonstrations for six tasks and show that policies trained on our force-informed actions achieve an average success rate of 76% across all tasks. In contrast, policies trained directly on actions that do not account for contact forces have near-zero success rates. We also conduct a study ablating the inclusion of force data in policy observations. We find that while using force data never hurts policy performance, it helps most for tasks that require advanced levels of precision and coordination, like opening an AirPods case and unscrewing a nut.

Tactile sensors provide critical information for contact-rich manipulation, yet tactile representations and policies remain tightly coupled to each specific sensor, limiting transferability across robots and hardware platforms. We propose TactX, a framework for learning a transferable tactile representation across sensors spanning three fundamentally different transduction modalities: resistive, magnetic, and vision-based. TactX maps heterogeneous tactile observations into a shared latent space through modality-specific encoders trained on paired contact data. Such paired interactions provide a natural alignment signal across modalities, and the encoders are jointly trained across all sensor pairs, inducing a consistent latent space for all sensor types. Our experiments show that TactX aligns tactile representations across sensors while preserving object-level contact information, as evidenced by sensor-identity prediction and object classification in the learned latent space. We evaluate TactX on four contact-rich manipulation tasks: pick-and-place, plug insertion, board wiping, and object reorientation, and show that policies trained with one sensor transfer zero-shot to physically distinct sensors through the shared latent. This improves the average success rate from 27.5% for vision-only policy to 45.9%, providing a step toward sensor-agnostic tactile manipulation.

While passive surfaces offer numerous benefits for interaction in mixed reality, reliably detecting touch input solely from head-mounted cameras has been a long-standing challenge. Camera specifics, hand self-occlusion, and rapid movements of both head and fingers introduce considerable uncertainty about the exact location of touch events. Existing methods have thus not been capable of achieving the performance needed for robust interaction. In this paper, we present a real-time pipeline that detects touch input from all ten fingers on any physical surface, purely based on egocentric hand tracking. Our method TouchInsight comprises a neural network to predict the moment of a touch event, the finger making contact, and the touch location. TouchInsight represents locations through a bivariate Gaussian distribution to account for uncertainties due to sensing inaccuracies, which we resolve through contextual priors to accurately infer intended user input. We first evaluated our method offline and found that it locates input events with a mean error of 6.3 mm, and accurately detects touch events (F1=0.99) and identifies the finger used (F1=0.96). In an online evaluation, we then demonstrate the effectiveness of our approach for a core application of dexterous touch input: two-handed text entry. In our study, participants typed 37.0 words per minute with an uncorrected error rate of 2.9% on average.

Vision-language-action (VLA) models typically inject proprioception only as a late conditioning signal, preventing robot state from grounding instruction understanding or directing visual attention. We introduce ThinkProprio, which discretizes proprioception into VLM-vocabulary tokens and uses them jointly with the instruction to gate visual patches before VLM computation, steering the model toward action-relevant evidence while discarding redundant tokens early. We find that proprioception added as a passive conditioning signal leaves performance essentially unchanged; its value emerges when token-form state acts as an active query that, with the instruction, selects which visual patches the VLM processes. Systematic ablations show that VLM-vocabulary tokens outperform learned projectors as the state encoding, and that retaining only about 12{\percent} of the visual tokens surpasses on CALVIN ABCtoD. Across CALVIN, LIBERO, and real-world manipulation, ThinkProprio reduces end-to-end inference latency while improving the matched full-token baseline.

We present N_0-Foundation, a paradigm for tactile-enabled embodied manipulation, which integrates tactile sensing hardware, large-scale multimodal data, tactile representation learning, and standardized evaluation. First, we engineer the infrastructure for scalable data collection, including a vision-based tactile sensor, a tactile Universal Manipulation Interface (UMI), and a synchronized visuo-tactile data collection system supporting both robot embodiments and UMI-based demonstrations. Leveraging this infrastructure, we construct NeoData, which contains more than 30000 hours of synchronized visual and tactile demonstrations, spanning six embodiments, 450 tasks, and billions of paired RGB and tactile frames collected through a mixture of real-robot teleoperation and UMI-based demonstrations. To facilitate open research, we further release OpenNeoData, a 5000-hour open-source subset of NeoData. The dataset addresses a central limitation of existing manipulation corpora, critical for deformable-object manipulation, precise assembly, delicate force control, and sustained surface interaction. Capitalizing on the large-scale, heterogeneous tactile measurements, we propose NeoForce, a visuo-tactile representation model that learn transferable tactile representations across different sensor designs. To enable systematic evaluation of tactile embodied models built upon our infrastructure, datasets and tactile representations, we further propose a comprehensive benchmark, which combines the real-world NeoReal suite and the simulated NeoSim suite for standardized evaluation. Experiments across both suites show that policies benefit from the physical contact state rather than from the device-specific appearance of the tactile signal. We release the dataset, the representation, and the benchmark, aiming at supporting future work on tactile-enabled embodied manipulation.

World action models improve robotic manipulation by conditioning actions on predicted futures, yet existing tactile variants largely inherit video-generation pipelines that reconstruct future tactile observations through iterative denoising. Such prediction can become unreliable under deployment drift: small changes in contact position or force may substantially alter tactile pixels even when the underlying contact evolution remains predictable. We introduce TacDyn-WAM, a heterogeneous visuo-tactile world action model that predicts implicit tactile dynamics rather than reconstructing future tactile observations. It learns TacRep, a dynamics-aware tactile target space trained through masked spatio-temporal prediction on tactile clips and regularized by relational structure distillation. A visual expert and an Implicit Tactile Dynamics Expert predict future visual and tactile representations in separate target spaces while interacting through joint attention; the tactile expert predicts future representations and their changes at multiple horizons in a single forward pass, and a read-only tactile memory supplies the current tactile state. On UniVTAC, TacDyn-WAM achieves an average success rate of 81.5% using only the provided demonstrations, reaching state-of-the-art-level performance and remaining competitive with models pretrained on large-scale visuo-tactile trajectories. Ablations confirm the benefits of both tactile pathways and TacRep over pixel-reconstruction and static alternatives. On five real-robot tasks, TacDyn-WAM reaches 71.0% average success, and modest-scale pretraining raises it to 85.0%, further validating our method.

Broader access to high-quality movement analysis could greatly benefit movement science and rehabilitation, such as allowing more detailed characterization of movement impairments and responses to interventions, or even enabling early detection of new neurological conditions or fall risk. While emerging technologies are making it easier to capture kinematics with biomechanical models, or how joint angles change over time, inferring the underlying physics that give rise to these movements, including ground reaction forces, joint torques, or even muscle activations, is still challenging. Here we explore whether imitation learning applied to a biomechanical model from a large dataset of movements from able-bodied and impaired individuals can learn to compute these inverse dynamics. Although imitation learning in human pose estimation has seen great interest in recent years, our work differences in several ways: we focus on using an accurate biomechanical model instead of models adopted for computer vision, we test it on a dataset that contains participants with impaired movements, we reported detailed tracking metrics relevant for the clinical measurement of movement including joint angles and ground contact events, and finally we apply imitation learning to a muscle-driven neuromusculoskeletal model. We show that our imitation learning policy, KinTwin, can accurately replicate the kinematics of a wide range of movements, including those with assistive devices or therapist assistance, and that it can infer clinically meaningful differences in joint torques and muscle activations. Our work demonstrates the potential for using imitation learning to enable high-quality movement analysis in clinical practice.

Joint contact forces govern implant longevity, cartilage health, and rehabilitation outcomes, shaping who develops osteoarthritis, who recovers well from joint replacement, and who benefits from biomechanical interventions. Yet they remain measurable only invasively, in a few dozen patients with instrumented implants. I present a physics-free pipeline to predict instantaneous 3D hip and knee contact forces from an uncalibrated monocular video: no markers, force plates, electromyography, subject-specific imaging, or musculoskeletal model. Parametric body meshes are recovered per frame, encoded as kinematic features, and decoded into forces by a transformer whose pose stream is adaptively modulated at every layer by body shape, joint, side, activity text, and self-supervised video tokens (V-JEPA 2), unifying hip and knee in a single model. Under leave-one-subject-out cross-validation across 26 patients and 25 activity categories from the in vivo OrthoLoad database, the pipeline matches the accuracy of subject-specific musculoskeletal simulations (0.32 pm 0.08 BW RMSE for hip; 0.23 pm 0.03 BW for knee) and resolves peak force changes smaller than those reported for gait retraining and osteoarthritis progression. Applied zero-shot to an independent instrumented cohort, it rivals or outperforms prior published methods. Even without curated activity labels, video features alone preserve accuracy and enable end-to-end inference on raw footage. Driven by the predictor, a generative motion prior produces biomechanically plausible variants with reduced peak loading, rediscovering strategies from the predictive simulation literature. This pipeline establishes uncalibrated monocular video as a viable modality for estimating joint loading, opening a path toward retrospective analysis of archived clinical recordings, primary-care screening, and at-home rehabilitation tracking.

Human skin provides a rich tactile sensing stream, localizing intentional and unintentional contact events over a large and contoured region. Replicating these tactile sensing capabilities for dexterous robotic manipulation systems remains a longstanding challenge. In this work, we take a step towards this goal by introducing DexSkin. DexSkin is a soft, conformable capacitive electronic skin that enables sensitive, localized, and calibratable tactile sensing, and can be tailored to varying geometries. We demonstrate its efficacy for learning downstream robotic manipulation by sensorizing a pair of parallel jaw gripper fingers, providing tactile coverage across almost the entire finger surfaces. We empirically evaluate DexSkin's capabilities in learning challenging manipulation tasks that require sensing coverage across the entire surface of the fingers, such as reorienting objects in hand and wrapping elastic bands around boxes, in a learning-from-demonstration framework. We then show that, critically for data-driven approaches, DexSkin can be calibrated to enable model transfer across sensor instances, and demonstrate its applicability to online reinforcement learning on real robots. Our results highlight DexSkin's suitability and practicality for learning real-world, contact-rich manipulation. Please see our project webpage for videos and visualizations: https://dex-skin.github.io/.

Hand-object interaction (HOI) is fundamental for humans to express intent. Existing HOI generation research is predominantly confined to fixed grasping patterns, where control is tied to physical priors such as force closure or generic intent instructions, even when expressed through elaborate language. Such an overly general conditioning imposes a strong inductive bias for stable grasps, thus failing to capture the diversity of daily HOI. To address these limitations, we introduce Free-Form HOI Generation, which aims to generate controllable, diverse, and physically plausible HOI conditioned on fine-grained intent, extending HOI from grasping to free-form interactions, like pushing, poking, and rotating. To support this task, we construct WildO2, an in-the-wild diverse 3D HOI dataset, which includes diverse HOI derived from internet videos. Specifically, it contains 4.4k unique interactions across 92 intents and 610 object categories, each with detailed semantic annotations. Building on this dataset, we propose TOUCH, a three-stage framework centered on a multi-level diffusion model that facilitates fine-grained semantic control to generate versatile hand poses beyond grasping priors. This process leverages explicit contact modeling for conditioning and is subsequently refined with contact consistency and physical constraints to ensure realism. Comprehensive experiments demonstrate our method's ability to generate controllable, diverse, and physically plausible hand interactions representative of daily activities. The project page is https://guangyid.github.io/hoi123touch{here}.

Enabling robots with contact-rich manipulation remains a pivotal challenge in robot learning, which is substantially hindered by the data collection gap, including its inefficiency and limited sensor setup. While prior work has explored handheld paradigms, their rod-based mechanical structures remain rigid and unintuitive, providing limited tactile feedback and posing challenges for human operators. Motivated by the dexterity and force feedback of human motion, we propose FreeTacMan, a human-centric and robot-free data collection system for accurate and efficient robot manipulation. Concretely, we design a wearable gripper with dual visuo-tactile sensors for data collection, which can be worn by human fingers for intuitive control. A high-precision optical tracking system is introduced to capture end-effector poses while synchronizing visual and tactile feedback simultaneously. We leverage FreeTacMan to collect a large-scale multimodal dataset, comprising over 3000k paired visual-tactile images with end-effector poses, 10k demonstration trajectories across 50 diverse contact-rich manipulation tasks. FreeTacMan achieves multiple improvements in data collection performance compared to prior works, and enables effective policy learning for contact-rich manipulation tasks with self-collected dataset. The full suite of hardware specifications and the dataset will be released to facilitate reproducibility and support research in visuo-tactile manipulation.

Significant progress has been made in vision-language models. However, language-conditioned robotic manipulation for contact-rich tasks remains underexplored, particularly in terms of tactile sensing. To address this gap, we introduce the Tactile-Language-Action (TLA) model, which effectively processes sequential tactile feedback via cross-modal language grounding to enable robust policy generation in contact-intensive scenarios. In addition, we construct a comprehensive dataset that contains 24k pairs of tactile action instruction data, customized for fingertip peg-in-hole assembly, providing essential resources for TLA training and evaluation. Our results show that TLA significantly outperforms traditional imitation learning methods (e.g., diffusion policy) in terms of effective action generation and action accuracy, while demonstrating strong generalization capabilities by achieving over 85\% success rate on previously unseen assembly clearances and peg shapes. We publicly release all data and code in the hope of advancing research in language-conditioned tactile manipulation skill learning. Project website: https://sites.google.com/view/tactile-language-action/

Reliable contact-rich manipulation requires detecting execution deviations early enough for corrective action. Yet most monitoring methods are reactive, identifying anomalies only after they become observable. Anticipating such anomalies is challenging because visual observations only partially reveal physical interaction, while planned actions describe intended motion rather than their actual physical consequences. We address this problem with MAIA, a multimodal framework for anomaly anticipation. Its vision-action-force world model learns nominal interaction dynamics and predicts the visual and force responses of planned actions, while a lightweight anomaly head predicts impending interaction anomalies. To enable systematic evaluation, we introduce CRIA, a real-world multimodal dataset of 2,852 trajectories spanning 18 contact-rich manipulation tasks, with frame-level annotations of anomaly onset and evolution. Experiments on both seen and novel tasks show that MAIA achieves more accurate anomaly discrimination than representative baselines while providing earlier warnings, with bACC scores of 0.765 and 0.710 and median anticipation lead times of 28.0 and 25.1 steps, respectively. Moreover, using these predictions for anomaly-aware action selection improves end-to-end task success from 52.6% to 61.5% without retraining the underlying manipulation policy. These results highlight the value of modeling future physical consequences for proactive anomaly anticipation.

Human-humanoid collaboration shows significant promise for applications in healthcare, domestic assistance, and manufacturing. While compliant robot-human collaboration has been extensively developed for robotic arms, enabling compliant human-humanoid collaboration remains largely unexplored due to humanoids' complex whole-body dynamics. In this paper, we propose a proprioception-only reinforcement learning approach, COLA, that combines leader and follower behaviors within a single policy. The model is trained in a closed-loop environment with dynamic object interactions to predict object motion patterns and human intentions implicitly, enabling compliant collaboration to maintain load balance through coordinated trajectory planning. We evaluate our approach through comprehensive simulator and real-world experiments on collaborative carrying tasks, demonstrating the effectiveness, generalization, and robustness of our model across various terrains and objects. Simulation experiments demonstrate that our model reduces human effort by 24.7%. compared to baseline approaches while maintaining object stability. Real-world experiments validate robust collaborative carrying across different object types (boxes, desks, stretchers, etc.) and movement patterns (straight-line, turning, slope climbing). Human user studies with 23 participants confirm an average improvement of 27.4% compared to baseline models. Our method enables compliant human-humanoid collaborative carrying without requiring external sensors or complex interaction models, offering a practical solution for real-world deployment.

The ability to associate touch with sight is essential for tasks that require physically interacting with objects in the world. We propose a dataset with paired visual and tactile data called Touch and Go, in which human data collectors probe objects in natural environments using tactile sensors, while simultaneously recording egocentric video. In contrast to previous efforts, which have largely been confined to lab settings or simulated environments, our dataset spans a large number of "in the wild" objects and scenes. To demonstrate our dataset's effectiveness, we successfully apply it to a variety of tasks: 1) self-supervised visuo-tactile feature learning, 2) tactile-driven image stylization, i.e., making the visual appearance of an object more consistent with a given tactile signal, and 3) predicting future frames of a tactile signal from visuo-tactile inputs.

Contact estimation is a key ability for limbed robots, where making and breaking contacts has a direct impact on state estimation and balance control. Existing approaches typically rely on gate-cycle priors or designated contact sensors. We design a contact estimator that is suitable for the emerging wheeled-biped robot types that do not have these features. To this end, we propose a Bayes filter in which update steps are learned from real-robot torque measurements while prediction steps rely on inertial measurements. We evaluate this approach in extensive real-robot and simulation experiments. Our method achieves better performance while being considerably more sample efficient than a comparable deep-learning baseline.

Estimating full-hand grasp pressure from egocentric video is critical for immersive VR and robotic manipulation, yet dense tactile sensing often relies on intrusive hardware. Existing vision-based methods predominantly rely on planar surfaces or fingertip contacts, failing to generalize to complex 3D object interactions. Therefore, we introduce EgoTactile, a benchmark pairing egocentric video with full-hand pressure supervision for diverse everyday objects, incorporating a bare-hand transfer subset to enable generalization to natural scenarios. Leveraging this benchmark, we first establish EgoPressureFormer as a discriminative baseline. Beyond this, to explicitly address the uncertainty in partial observations, we propose EgoPressureDiff, a conditional diffusion framework that adapts a large-scale pre-trained video diffusion backbone. By combining rich world knowledge priors with a Physically-Informed Feature Rectification layer to inject semantic constraints, our approach effectively infers plausible contact patterns and resolves visual-physical ambiguities. Extensive experiments demonstrate that our method achieves superior performance on the benchmark and robust transferability to in-the-wild scenarios. Our project page is available at https://egotactile.github.io/.

Human demonstrations are a scalable data source for learning robot manipulation policies. However, common sources of human demonstration data, such as motion-capture trajectories and internet videos, capture mostly motion and appearance while missing the contact forces that are critical for force-sensitive manipulation. In this paper, we introduce ForceBand, a low-cost wrist-worn sEMG system that turns human muscle activity into force-enriched demonstrations. We first collect a 10-hour multimodal dataset containing egocentric video, sEMG, IMU, and fingertip force measurements across diverse actions and objects. Using this dataset, we pre-train an EMG2Force model that predicts per-finger forces from sEMG and IMU signals. After a short user-specific calibration, users can collect target-task demonstrations using only ForceBand and video; EMG2Force then labels these demonstrations with per-finger force traces, producing force-augmented demonstrations for robot policy learning. Experiments show that ForceBand recovers fine-grained fingertip interactions with over 50% lower force prediction error than vision-based baselines and achieves an 87% success rate on pick, squeeze, and place tasks that require object-specific force control across objects with diverse shapes, sizes, and weights. Project website: https://forceband-emg.github.io

Supervised visuomotor policies have shown strong performance in robotic manipulation but often struggle in tasks with limited visual inputs, such as operations in confined spaces and dimly lit environments, or tasks requiring precise perception of object properties and environmental interactions. In such cases, tactile feedback becomes essential for manipulation. While the rapid progress of supervised visuomotor policies has benefited greatly from high-quality, reproducible simulation benchmarks in visual imitation, the visuotactile domain still lacks a similarly comprehensive and reliable benchmark for large-scale and rigorous evaluation. To address this, we introduce ManiFeel, a reproducible and scalable simulation benchmark designed to systematically study supervised visuotactile policy learning. ManiFeel offers a diverse suite of contact-rich and visually challenging manipulation tasks, a modular evaluation pipeline spanning sensing modalities, tactile representations, and policy architectures, as well as real-world validation. Through extensive experiments, ManiFeel demonstrates how tactile sensing enhances policy performance across diverse manipulation scenarios, ranging from precise contact-driven operations to visually constrained settings. In addition, the results reveal task-dependent strengths of different tactile modalities and identify key design principles and open challenges for robust visuotactile policy learning. Real-world evaluations further confirm that ManiFeel provides a reliable and meaningful foundation for benchmarking and future visuotactile policy development. To foster reproducibility and future research, we will release our codebase, datasets, training logs, and pretrained checkpoints, aiming to accelerate progress toward generalizable visuotactile policy learning and manipulation.

Inferring human-scene contact (HSC) is the first step toward understanding how humans interact with their surroundings. While detecting 2D human-object interaction (HOI) and reconstructing 3D human pose and shape (HPS) have enjoyed significant progress, reasoning about 3D human-scene contact from a single image is still challenging. Existing HSC detection methods consider only a few types of predefined contact, often reduce body and scene to a small number of primitives, and even overlook image evidence. To predict human-scene contact from a single image, we address the limitations above from both data and algorithmic perspectives. We capture a new dataset called RICH for "Real scenes, Interaction, Contact and Humans." RICH contains multiview outdoor/indoor video sequences at 4K resolution, ground-truth 3D human bodies captured using markerless motion capture, 3D body scans, and high resolution 3D scene scans. A key feature of RICH is that it also contains accurate vertex-level contact labels on the body. Using RICH, we train a network that predicts dense body-scene contacts from a single RGB image. Our key insight is that regions in contact are always occluded so the network needs the ability to explore the whole image for evidence. We use a transformer to learn such non-local relationships and propose a new Body-Scene contact TRansfOrmer (BSTRO). Very few methods explore 3D contact; those that do focus on the feet only, detect foot contact as a post-processing step, or infer contact from body pose without looking at the scene. To our knowledge, BSTRO is the first method to directly estimate 3D body-scene contact from a single image. We demonstrate that BSTRO significantly outperforms the prior art. The code and dataset are available at https://rich.is.tue.mpg.de.

Palpation, the use of touch in medical examination, is almost exclusively performed by humans. We investigate a proof of concept for an artificial palpation method based on self-supervised learning. Our key idea is that an encoder-decoder framework can learn a representation from a sequence of tactile measurements that contains all the relevant information about the palpated object. We conjecture that such a representation can be used for downstream tasks such as tactile imaging and change detection. With enough training data, it should capture intricate patterns in the tactile measurements that go beyond a simple map of forces -- the current state of the art. To validate our approach, we both develop a simulation environment and collect a real-world dataset of soft objects and corresponding ground truth images obtained by magnetic resonance imaging (MRI). We collect palpation sequences using a robot equipped with a tactile sensor, and train a model that predicts sensory readings at different positions on the object. We investigate the representation learned in this process, and demonstrate its use in imaging and change detection.

Robotic manipulation requires both rich multimodal perception and effective learning frameworks to handle complex real-world tasks. See-through-skin (STS) sensors, which combine tactile and visual perception, offer promising sensing capabilities, while modern imitation learning provides powerful tools for policy acquisition. However, existing STS designs lack simultaneous multimodal perception and suffer from unreliable tactile tracking. Furthermore, integrating these rich multimodal signals into learning-based manipulation pipelines remains an open challenge. We introduce TacThru, an STS sensor enabling simultaneous visual perception and robust tactile signal extraction, and TacThru-UMI, an imitation learning framework that leverages these multimodal signals for manipulation. Our sensor features a fully transparent elastomer, persistent illumination, novel keyline markers, and efficient tracking, while our learning system integrates these signals through a Transformer-based Diffusion Policy. Experiments on five challenging real-world tasks show that TacThru-UMI achieves an average success rate of 85.5%, significantly outperforming the baselines of alternating tactile-visual (66.3%) and vision-only (55.4%). The system excels in critical scenarios, including contact detection with thin and soft objects and precision manipulation requiring multimodal coordination. This work demonstrates that combining simultaneous multimodal perception with modern learning frameworks enables more precise, adaptable robotic manipulation.

We introduce PhysLadder, a hierarchical Sim-Real benchmark for evaluating physical interaction capabilities in contact-rich manipulation. Its 16 household tasks span three cumulative levels: contact selection and geometric alignment (L1), force regulation within sustained contact (L2), and coordinated contact reconfiguration and force regulation (L3). Each task is instantiated in physically and visually matched simulated and real-world environments, with shared task definitions and success criteria. We evaluate GPT-6 Astra zero-shot with three trials per task in each environment. Real-world success rates decline from 80.0% at L1 to 47.6% at L2 and 0.0% at L3, with corresponding simulation rates of 66.7%, 47.6%, and 0.0%. Ten of the 16 tasks have identical success counts across environments; the remaining six differ by one success out of three trials. Across both environments, recurring difficulties in spatial reasoning, contact selection, force regulation, and coordination often prevent local physical progress from accumulating into task completion. These findings characterize Astra's observed capability boundary across increasing interaction demands and, for this model, support matched simulation as a repeatable, scalable testbed for studying the sustained, coordinated physical interactions that limit reliable manipulation.

Handheld grippers are increasingly used to collect human demonstrations due to their ease of deployment and versatility. However, most existing designs lack tactile sensing, despite the critical role of tactile feedback in precise manipulation. We present a portable, lightweight gripper with integrated tactile sensors that enables synchronized collection of visual and tactile data in diverse, real-world, and in-the-wild settings. Building on this hardware, we propose a cross-modal representation learning framework that integrates visual and tactile signals while preserving their distinct characteristics. The learning procedure allows the emergence of interpretable representations that consistently focus on contacting regions relevant for physical interactions. When used for downstream manipulation tasks, these representations enable more efficient and effective policy learning, supporting precise robotic manipulation based on multimodal feedback. We validate our approach on fine-grained tasks such as test tube insertion and pipette-based fluid transfer, demonstrating improved accuracy and robustness under external disturbances. Our project page is available at https://binghao-huang.github.io/touch_in_the_wild/ .

Handheld devices have opened up unprecedented opportunities to collect large-scale, high-quality demonstrations efficiently. However, existing systems often lack robust tactile sensing or reliable pose tracking to handle complex interaction scenarios, especially for bimanual and contact-rich tasks. In this work, we propose ViTaMIn-B, a more capable and efficient handheld data collection system for such tasks. We first design DuoTact, a novel compliant visuo-tactile sensor built with a flexible frame to withstand large contact forces during manipulation while capturing high-resolution contact geometry. To enhance the cross-sensor generalizability, we propose reconstructing the sensor's global deformation as a 3D point cloud and using it as the policy input. We further develop a robust, unified 6-DoF bimanual pose acquisition process using Meta Quest controllers, which eliminates the trajectory drift issue in common SLAM-based methods. Comprehensive user studies confirm the efficiency and high usability of ViTaMIn-B among novice and expert operators. Furthermore, experiments on four bimanual manipulation tasks demonstrate its superior task performance relative to existing systems. Project page: https://chuanyune.github.io/ViTaMIn-B_page/

If human experience is any guide, operating effectively in unstructured environments -- like homes and offices -- requires robots to sense the forces during physical interaction. Yet, the lack of a versatile, accessible, and easily customizable tactile sensor has led to fragmented, sensor-specific solutions in robotic manipulation -- and in many cases, to force-unaware, sensorless approaches. With eFlesh, we bridge this gap by introducing a magnetic tactile sensor that is low-cost, easy to fabricate, and highly customizable. Building an eFlesh sensor requires only four components: a hobbyist 3D printer, off-the-shelf magnets (<$5), a CAD model of the desired shape, and a magnetometer circuit board. The sensor is constructed from tiled, parameterized microstructures, which allow for tuning the sensor's geometry and its mechanical response. We provide an open-source design tool that converts convex OBJ/STL files into 3D-printable STLs for fabrication. This modular design framework enables users to create application-specific sensors, and to adjust sensitivity depending on the task. Our sensor characterization experiments demonstrate the capabilities of eFlesh: contact localization RMSE of 0.5 mm, and force prediction RMSE of 0.27 N for normal force and 0.12 N for shear force. We also present a learned slip detection model that generalizes to unseen objects with 95% accuracy, and visuotactile control policies that improve manipulation performance by 40% over vision-only baselines -- achieving 91% average success rate for four precise tasks that require sub-mm accuracy for successful completion. All design files, code and the CAD-to-eFlesh STL conversion tool are open-sourced and available on https://e-flesh.com.

Humanoid loco-manipulation is often simplified into a stop-and-go process: walking to an object, stopping to manipulate it, and then resuming locomotion. It also commonly relies on low degree-of-freedom (DoF) end effectors that behave like an open-close grasp primitive. We introduce CoorDex, a learning pipeline that converts high-dimensional body and dexterous hand control into coordinated latent residual control, enabling high-DoF dexterous loco-manipulation on the move. Starting from simulated whole-body and hand demonstrations, CoorDex trains privileged motion tracking teachers for the humanoid body and dexterous hand, distills them into proprioception-conditioned latent priors, and uses the frozen priors as the action space for downstream residual reinforcement learning. A coordinated latent residual policy composes these priors through shared task context and separate body-hand residual heads, preserving natural whole-body motion while improving finger-level contact reliability. CoorDex enables a Unitree G1 humanoid with a 20-DoF WUJI hand to execute dexterous manipulation while in motion, including non-stop bottle grasping and carrying, fridge door opening on the move, and cube pick-and-turn. Ablations on the walk-grasp-carry task show that joint-space PPO, joint-space hand control, and monolithic latent prediction all fail under the same reward budget, while the latent-prior interface and coordinated residual structure make high-dimensional contact-rich loco-manipulation trainable. Project Page: https://skevinci.github.io/coordex/

Video-Action Models (VAMs) have emerged as a promising framework for embodied intelligence, learning implicit world dynamics from raw video streams to produce temporally consistent action predictions. Although such models demonstrate strong performance on long-horizon tasks through visual reasoning, they remain limited in contact-rich scenarios where critical interaction states are only partially observable from vision alone. In particular, fine-grained force modulation and contact transitions are not reliably encoded in visual tokens, leading to unstable or imprecise behaviors. To bridge this gap, we introduce the Video-Tactile Action Model (VTAM), a multimodal world modeling framework that incorporates tactile perception as a complementary grounding signal. VTAM augments a pretrained video transformer with tactile streams via a lightweight modality transfer finetuning, enabling efficient cross-modal representation learning without tactile-language paired data or independent tactile pretraining. To stabilize multimodal fusion, we introduce a tactile regularization loss that enforces balanced cross-modal attention, preventing visual latent dominance in the action model. VTAM demonstrates superior performance in contact-rich manipulation, maintaining a robust success rate of 90 percent on average. In challenging scenarios such as potato chip pick-and-place requiring high-fidelity force awareness, VTAM outperforms the pi 0.5 baseline by 80 percent. Our findings demonstrate that integrating tactile feedback is essential for correcting visual estimation errors in world action models, providing a scalable approach to physically grounded embodied foundation models.

World Action Models (WAMs) generate actions together with predicted futures, offering a powerful interface for robot decision making. In contact-rich manipulation, however, visually plausible futures can be physically incomplete: insertion, assembly, search, and reorientation often depend on slip, jamming, contact normals, or small alignment errors that are weakly visible or hidden in RGB. A natural solution is to predict future tactile states, however, we identify tactile pollution, a failure mode where unconstrained tactile-token injection degrades video and action prediction by forcing a visual dynamics model to absorb sparse, local, event-driven contact signals. To address this, we propose Tactile-WAM, a touch-aware WAM with a Tactile Asymmetric Attention Mechanism (TAAM). TAAM combines a VideoClean mask, which blocks video-query access to tactile key/value tokens while preserving action-query access, with a touch-aware bias for action attention. The VideoClean mask protects visual prediction while keeping contact information available for action generation; the touch-aware bias is derived from predicted touch changes and modulates action attention to tactile tokens during denoising. On ManiFeel, Tactile-WAM improves the mean success rate by 38.9% overall and by 86% on contact-rich tasks.